2024-01-08

Electromechanical Brake Booster Assembly (Non-Structural Pack) (LHD) (Remove & Replace)

Correction code 33201002 1.56 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-12-27: 후드 내 보관 유닛, 12V 배터리 및 와이퍼 모듈 탈거 및 장착 단계가 삭제되었습니다.
  • 1079041-00-A 플레어 너트 크로우풋 세트

Torque Specifications

표 1. Torque Specifications: Electromechanical Brake Booster Assembly (Non-Structural Pack) (LHD) (Remove & Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
전면 브레이크 라인 패스너
16 Nm (11.8 lbs-ft)
  • 12mm 12pt 콤비네이션 렌치
  • 12mm 플레어 너트 크로우풋 소켓
Reuse
후면 브레이크 라인 패스너
16 Nm (11.8 lbs-ft)
  • 12mm 12pt 콤비네이션 렌치
  • 12mm 플레어 너트 크로우풋 소켓
Reuse
브레이크 부스터를 벌크헤드에 고정하는 너트
16.5 Nm (12.2 lbs-ft)
  • 13mm 딥소켓
  • 6인치 익스텐션
Replace

Remove

  1. LH 전면 도어를 열고 LH 전면 창문을 완전히 내립니다.
  2. 운전석 시트를 완전히 뒤로 이동합니다.
  3. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  4. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  5. HEPA 필터 어셈블리를 탈거합니다. 참조 항목: Assembly - Filter - HEPA (Remove and Install).
  6. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  7. 잠금 탭을 풀고 브레이크 오일 저장 탱크 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  8. 잠금 탭을 분리한 다음 브레이크 부스터 어셈블리에서 하네스 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  9. 브레이크 부스터와 탱크 부위 아래에 흡수재를 배치합니다.
  10. 브레이크 오일 주사기를 사용하여 저장 탱크에서 브레이크 오일을 제거합니다.
  11. 전면 브레이크 라인을 마스터 실린더에서 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12mm 12pt 콤비네이션 렌치
    • 12mm 플레어 너트 크로우풋 소켓
  12. 후면 브레이크 라인을 마스터 실린더에서 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12mm 12pt 콤비네이션 렌치
    • 12mm 플레어 너트 크로우풋 소켓
  13. 운전석 무릎 에어백을 탈거합니다. 참조 항목: Airbag - Knee - Driver (Remove and Install).
  14. LH 발밑 공간 에어 덕트를 탈거합니다. 참조 항목: Duct - Footwell - LH (Remove and Replace).
  15. 브레이크 스위치 전기 커넥터를 연결 해제합니다.
  16. 페달 어셈블리에서 브레이크 스위치를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    스위치를 45도 돌려 어셈블리에서 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    탈거 중에 손상된 경우 교체합니다.
  17. 브레이크 페달 어셈블리의 클레비스 핀에서 코터 클립을 탈거합니다.
  18. 브레이크 페달 어셈블리에서 클레비스 핀을 탈거합니다.
  19. 브레이크 부스터를 벌크헤드에 고정하는 너트를 탈거하여 폐기한 다음 차량에서 브레이크 부스터 어셈블리를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 딥소켓
    • 6인치 익스텐션

Install

  1. 브레이크 부스터 어셈블리를 차량에 배치합니다.
  2. 브레이크 부스터를 벌크헤드에 고정하는 새 너트를 장착합니다.
    16.5 Nm (12.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 딥소켓
    • 6인치 익스텐션
  3. 브레이크 페달을 iBooster 로드와 정렬한 다음 클레비스 핀을 브레이크 페달 어셈블리에 장착합니다.
  4. 브레이크 페달 어셈블리의 클레비스 핀에 코터 클립을 장착합니다.
  5. 브레이크 스위치 전기 커넥터를 연결합니다.
  6. LH 발밑 공간 에어 덕트를 장착합니다. 참조 항목: Duct - Footwell - LH (Remove and Replace).
  7. 운전석 무릎 에어백을 장착합니다. 참조 항목: Airbag - Knee - Driver (Remove and Install).
  8. 후면 브레이크 라인을 마스터 실린더에 연결합니다.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12mm 12pt 콤비네이션 렌치
    • 12mm 플레어 너트 크로우풋 소켓
  9. 전면 브레이크 라인을 마스터 실린더에 연결합니다.
    16 Nm (11.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 12mm 12pt 콤비네이션 렌치
    • 12mm 플레어 너트 크로우풋 소켓
  10. 브레이크 오일 저장 탱크 캡 주변 부위를 깨끗이 하고 캡을 탈거합니다.
  11. 브레이크 오일 저장 탱크를 "MAX" 레벨까지 채웁니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    도장면에 브레이크 오일이 묻지 않도록 주의해야 합니다. 남은 브레이크 오일을 작업용 타월로 씻어냅니다.
  12. 브레이크 부스터와 탱크 부위 아래에서 흡수재를 제거합니다.
  13. 하네스 커넥터를 브레이크 부스터 어셈블리에 연결한 다음 잠금 탭을 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  14. 브레이크 오일 저장 탱크 전기 커넥터를 연결한 다음 잠금 탭을 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  15. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  16. 펌웨어를 다시 배포합니다. 참조 항목: Software Reinstall - Toolbox.
  17. 브레이크를 블리딩합니다. 참조 항목: Brake Fluid Bleed/Flush.
  18. HEPA 필터 어셈블리를 장착합니다. 참조 항목: Assembly - Filter - HEPA (Remove and Install).
  19. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  20. 정비 모드를 비활성화합니다. 참조 항목: Service Mode.
  21. LH 전면 시트를 원래 위치로 이동합니다.
  22. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.
  23. 리프트에서 차량을 내립니다.
  24. 시험 주행을 수행합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    필요에 따라 교정 코드 00040100을 추가합니다.