2024-08-16

Fascia - Rear (Remove and Install)

Correction code 10013001 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-09-05: 이동식 정비 서비스 및 작업 보조 관련 더 직접적인 지침을 포함하도록 후면 페시아 탈거 단계를 업데이트했습니다.
  • 2023-10-08: HW4 차량용 후면 페시아 전기 하네스 연결 해제/연결 단계를 건너뛰도록 명시한 참고 사항을 추가했습니다.

Torque Specifications

표 1. Torque Specifications: Fascia - Rear (Remove and Install)
Description Torque Value Recommended Tools Reuse/Replace Notes
후면 페시아의 모서리를 차체에 고정하는 볼트
4 Nm (2.9 lbs-ft)
  • 10mm 육각
Reuse
후면 디퓨저를 차체에 고정하는 볼트
4 Nm (2.9 lbs-ft)
  • 10mm 소켓
  • 2인치 익스텐션
Reuse
후면 페시아의 측면을 차체에 고정하는 볼트
4 Nm (2.9 lbs-ft)
  • 8mm 육각
  • 4인치 익스텐션
Reuse

Remove

  1. LH 및 RH 테일라이트를 탈거합니다. 참조 항목: Taillight - LH (Remove and Replace).
  2. 차량의 양쪽에서 후면 페시아 모서리를 차체에 고정하는 볼트를 탈거합니다.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 육각
  3. 후면 페시아를 후면 디퓨저에 고정하는 볼트(7개) 및 클립(6개)을 탈거합니다.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
  4. LH 후면 펜더 가니시를 탈거합니다. 참조 항목: Garnish - Fender - Rear - LH (Remove and Replace).
  5. 후면 페시아의 LH 쪽을 차체에 고정하는 볼트를 탈거합니다.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8mm 육각
    • 4인치 익스텐션
  6. 차량 RH에 대해 4단계 및 5단계를 반복합니다.
  7. HW3 차량의 경우, 후면 페시아 전기 하네스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    HW4 차량의 경우 해당 단계는 건너뜁니다.
  8. 후방 페시아를 차량에서 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    모서리 패스너 클립이 후면 쿼터 패널을 손상하지 않도록 후면 페시아를 차체에서 조심스럽게 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    가능하다면 차량에서 후면 페시아를 탈거할 때 보조 작업자가 있는 것이 좋습니다. 이동식 정비 서비스의 경우 작업 보조가 필수는 아닙니다.

Install

  1. 후면 페시아를 차량에 장착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    모서리 패스너 클립이 후면 쿼터 패널을 손상하지 않도록 후면 페시아를 차체에 조심스럽게 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    가능하다면 차량에서 후면 페시아를 장착할 때 보조 작업자가 있는 것이 좋습니다.
  2. HW3 차량의 경우, 후면 페시아 전기 하네스를 연결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    HW4 차량의 경우 해당 단계는 건너뜁니다.
  3. 후면 페시아의 LH 쪽을 차체에 고정하는 볼트를 장착합니다.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8mm 육각
    • 4인치 익스텐션
  4. LH 후면 펜더 가니시를 장착합니다. 참조 항목: Garnish - Fender - Rear - LH (Remove and Replace).
  5. 차량 RH에서 3단계와 4단계를 반복합니다.
  6. 후면 디퓨저 볼트에 나사 고정제를 도포한 다음 후면 페시아를 후면 디퓨저에 고정하는 볼트(7개)와 클립(6개)을 장착합니다.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
  7. 차량의 양쪽에서 후면 페시아 모서리를 차체에 고정하는 볼트를 장착합니다.
    4 Nm (2.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 육각
  8. LH 및 RH 테일라이트를 장착합니다. 참조 항목: Taillight - LH (Remove and Replace).