2026-11-03

혼 - 스티어링 휠(탈거 및 교체)

교정 코드 32050012 0.18 메모: 절차에서 명시적으로 언급하지 않는 한 교정 코드 및 해당 관련 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-11-03: Updated the specification of the bolts (x4) that attach the bright surround to the steering wheel.
  • 2026-08-10: Added batch information about the bolts (x4) that attach the bright surround to the steering wheel.

토크 규격

Table 1. 토크 규격: 혼 - 스티어링 휠(탈거 및 교체)
설명 토크 값 권장 공구 재사용/교체 참고
Bolts (x4) that attach the bright surround to the steering wheel
2.5 Nm (1.8 lbs-ft)
1.8 Nm (1.3 lbs-ft)
  • Torx T25 bit
  • PH1 Stubby Phillips Screwdriver
 재사용

T25 bolts: 2.5 Nm

PH1 bolts: 1.8 Nm

탈거

  1. Disconnect 12V power. See 12V/LV 전원(연결 해제 및 연결).
  2. Remove the driver airbag. See 에어백 - 운전석(탈거 및 교체).
  3. Disconnect the steering wheel wiring harness electrical connector.
  4. Disconnect the LH steering wheel switch electrical connector. Repeat this step for the RH steering wheel switch electrical connector.
    Figure 1. LH shown, RH similar
  5. Release clips (x3) that attach the horn to the steering wheel assembly.
    Note
    Pull the horn assembly straight out to release it.
  6. Remove the bolts (x4) that attach the steering wheel bright surround to the steering wheel.
    Note
    Depending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.
    Note
    Pry the lower portion of the bright surround assembly away from the steering wheel, and then work your way around. Do not remove it now. Wait until the steering wheel is removed.
    Tip
    다음 공구를 사용하는 것이 좋습니다.
    • Torx T25 bit
    • PH1 Stubby Phillips Screwdriver
  7. Disconnect the lower connection from the steering wheel controller, and then remove the steering wheel horn assembly from the steering wheel.
  8. Disconnect the steering wheel horn assembly harness electrical connectors.
  9. Release the clip that attaches the steering wheel harness to the horn assembly.

장착

  1. Fasten the clip that attaches the steering wheel harness to the horn assembly.
  2. Connect the steering wheel horn assembly harness electrical connectors.
  3. Position the steering wheel surround onto the steering wheel, and then install the bolts.
    2.5 Nm (1.8 lbs-ft)
    1.8 Nm (1.3 lbs-ft)
    Note
    Depending on the vehicle batch, some vehicles are equipped with T25 bolts while others are equipped with PH1 bolts.
    Note
    Torque the T25 bolts to 2.5 Nm; torque the PH1 bolts to 1.8 Nm.
    Tip
    다음 공구를 사용하는 것이 좋습니다.
    • Torx T25 bit
    • PH1 Stubby Phillips Screwdriver
  4. Position the horn assembly to the steering wheel, and then fasten the clips.
  5. Connect the LH steering wheel switch electrical connector. Repeat this step for the RH steering wheel switch electrical connector.
    Figure 2. LH shown, RH similar
  6. Connect the lower electrical connector on the steering wheel controller.
  7. Connect the steering wheel electrical wiring harness connector.
  8. Install the driver airbag. See 에어백 - 운전석(탈거 및 교체).
  9. Connect 12V power. See 12V/LV 전원(연결 해제 및 연결).