2023-02-28

Module - Inductive Charger - Center Console (2.0) (Remove and Replace)

Correction code 15193902 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 전면 도어를 열고 전면 창문을 내립니다.
  2. 전면 시트를 가장 뒤쪽 낮은 위치로 이동합니다.
  3. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  4. 12V/LV 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  5. 접근을 위해 센터콘솔 암레스트를 위로 회전합니다.
  6. 센터콘솔 장식 트림을 센터콘솔에 고정하는 클립(17개)을 분리한 다음 커넥터를 연결 해제하고 센터콘솔에서 장식 트림을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    먼저 주변 클립을 분리한 다음 트림의 전면 상단부를 분리합니다.
  7. 센터콘솔 유도식 충전기 모듈을 장식 트림에 고정하는 나사(3개)를 탈거합니다.
    1.3 Nm (1.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  8. 고정 탭(2개) 및 위치 지정 탭(2개)을 분리하여 센터콘솔 장식 트림에서 유도식 충전기 모듈을 탈거합니다.

Install

  1. 센터콘솔 유도식 충전기 모듈을 센터콘솔 장식 트림에 배치한 다음 고정 탭(2개) 및 위치 지정 탭(2개)을 고정합니다.
  2. 센터콘솔 유도식 충전기 모듈을 장식 트림에 고정하는 나사(3개)를 장착합니다.
    1.3 Nm (1.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
  3. 센터콘솔 장식 트림 어셈블리를 센터콘솔에 배치하고 커넥터를 연결한 다음 장식 트림을 센터콘솔에 고정하는 클립(17개)을 조입니다.
  4. 센터콘솔 암레스트를 닫습니다.
  5. 12V/LV 전원을 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  6. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  7. 후드를 닫습니다.
  8. 전면 시트를 원래 위치로 이동합니다.
  9. 전면 창문을 올리고 전면 도어를 닫습니다.