2024-06-11

Bracket - Brake Caliper - Rear - LH (Remove and Replace)

Correction code 33010532 0.72 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-05-28: 참조 및 주의 사항을 업데이트했습니다.

Torque Specifications

표 1. 토크 규격: Bracket - Brake Caliper - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 후면 브레이크 캘리퍼를 LH 후면 브레이크 캘리퍼 브래킷에 고정하는 볼트(2개)
26.5 Nm (19.5 lbs-ft)
  • 14mm 소켓
Reuse
LH 후면 브레이크 캘리퍼 브래킷을 LH 후면 너클에 고정하는 볼트(2개)
83 Nm (61.2 lbs-ft)
  • 외부 Torx E18
Replace

Remove

  1. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  2. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  3. LH 후면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  4. LH 후면 브레이크 캘리퍼를 LH 후면 브레이크 캘리퍼 브래킷에 고정하는 볼트(2개)를 탈거합니다.
    26.5 Nm (19.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 14mm 소켓
  5. LH 후면 캘리퍼를 어셈블리에서 탈거한 다음 안전한 위치에 S자형 고리로 지지합니다.
  6. LH 후면 브레이크 캘리퍼 브래킷에서 LH 후면 브레이크 패드(2개)를 탈거합니다.
  7. LH 후면 브레이크 캘리퍼 브래킷 받침대 클립(4개)을 탈거합니다.
  8. LH 후면 브레이크 캘리퍼 브래킷을 LH 후면 너클에 고정하는 볼트(2개)를 탈거하여 폐기한 다음 너클에서 브래킷을 탈거합니다.
    83 Nm (61.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E18

Install

  1. LH 후면 브레이크 캘리퍼 브래킷을 LH 후면 너클에 배치한 다음 브래킷을 너클에 고정하는 새 볼트(2개)를 장착합니다.
    83 Nm (61.2 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    To prevent damage to the flexible brake hose, make sure that the brake hose is not twisted and can bend forward and does not make contact with the wheel arch liner when the vehicle is lowered.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E18
  2. LH 후면 브레이크 캘리퍼 브래킷 받침대 클립(4개)을 장착합니다.
  3. LH 브레이크 패드 접촉 지점 상단 및 하단에 Silaramic 윤활제를 고르게 도포합니다.
  4. LH 후면 브레이크 캘리퍼 브래킷에 LH 후면 브레이크 패드(2개)를 장착합니다.
  5. LH 후면 브레이크 캘리퍼를 LH 후면 브레이크 캘리퍼 브래킷에 고정하는 볼트(2개)를 장착합니다.
    26.5 Nm (19.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 14mm 소켓
  6. LH 후면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  7. 주차 버튼을 길게 눌러 EPB 정비 모드를 해제합니다.
  8. 리프트에서 차량을 내립니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  9. 도로 테스트를 수행하여 브레이크 페달의 느낌과 성능이 적절한지 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    현재 FRT 기준(00040100).