2024-04-08

Hose - Front Manifold - RH (Remove and Replace)

Correction code 18309402 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  2. LH 전면 도어를 열고 LH 전면 창문을 완전히 내립니다.
  3. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  4. 외기 흡기 덕트를 탈거합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  5. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. 전면 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  7. HV 배터리에서 LH 및 RH 전면 휠 라이너를 분리합니다.
    그림 1. LH에서 본 모습, RH도 유사함
  8. 전면 HV 배터리 스키드 플레이트를 탈거합니다. 참조 항목: Skid Plate - HV Battery - Front (Remove and Replace).
  9. 냉각수 배출 용기를 HV 배터리의 RH 전면 아래에 배치합니다.
  10. 스프링 클립을 탈거하고 HV 배터리의 RH 전면에서 RH 전면 매니폴드 호스를 연결 해제한 다음 즉시 HV 배터리 쪽에 플러그를 장착합니다.
  11. 냉각수 배출 용기를 HV 배터리의 전면 오른쪽 중앙 아래에 배치합니다.
  12. 스프링 클립을 탈거하고 HV 배터리의 전면에서 RH 전면 매니폴드 호스를 연결 해제한 다음 즉시 암수 피팅에 플러그를 장착합니다.
  13. 냉각수 배출 용기를 HV 배터리 매니폴드 호스 아래에 배치합니다.
  14. 스프링 클립을 분리하고 LH 매니폴드 튜브에서 RH 전면 매니폴드 호스를 연결 해제한 다음 암수 피팅에 즉시 플러그를 장착합니다.

Install

  1. 냉각수 플러그를 탈거하고 LH 전면 매니폴드 호스에서 RH 전면 매니폴드 호스를 연결한 다음 스프링 클립을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the hose is fully seated.
  2. 냉각수 배출 용기를 HV 배터리의 전면 오른쪽 중앙 아래에 배치합니다.
  3. 냉각수 플러그를 탈거하고 RH 전면 매니폴드 호스를 HV 배터리 전면에 연결한 다음 스프링 클립을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the hose is fully seated.
  4. 냉각수 배출 용기를 HV 배터리의 RH 전면 아래에 배치합니다.
  5. 냉각수 플러그를 탈거하고 RH 전면 매니폴드 호스를 HV 배터리 RH 전면에 연결한 다음 스프링 클립을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the hose is fully seated.
  6. 차량 아래에서 냉각수 배출 용기를 치웁니다.
  7. 전면 HV 배터리 스키드 플레이트를 장착합니다. 참조 항목: Skid Plate - HV Battery - Front (Remove and Replace).
  8. LH 및 RH 전면 휠 라이너를 HV 배터리에 장착합니다.
    그림 2. LH에서 본 모습, RH도 유사함
  9. 전면 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  10. 차량을 완전히 내립니다.
  11. 냉각수 보틀 캡을 탈거한 다음 냉각수를 적절한 수위까지 채웁니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각수 수위가 “Max” 선에 있는지 확인합니다.
  12. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  13. Toolbox 3.0이 설치된 노트북으로 차량에 연결합니다.
  14. Toolbox에서 Actions/Autodiag 탭을 클릭한 다음 "Purge"를 검색합니다.
  15. TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    을(를) 클릭한 다음 Run을 클릭하고 루틴이 완료될 때까지 기다립니다.
  16. 냉각수 수위를 검사하고 필요에 따라 보충한 다음 냉각수 보틀 캡을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각수 수위가 “Max” 선에 있는지 확인합니다.
  17. 차량에서 노트북을 연결 해제합니다.
  18. 외기 흡기 덕트를 장착합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  19. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.