2024-09-09

Hub - Rear - LH (Remove and Replace)

Correction code 31030702 0.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-01-19: EPB 정비 모드 참조를 업데이트했습니다.
  • 2023-11-13: 허브 풀러 공구가 업데이트되어 브레이크 로터 볼트를 제거하는 단계 순서를 변경했습니다.

토크 규격

표 1. Torque Specifications: Hub - Rear - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 후면 허브 및 베어링을 LH 후면 너클에 고정하는 볼트
85 Nm (62.7 lbs-ft)
  • 18mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 3인치 익스텐션
Reuse
LH 후면 로터를 LH 후면 허브에 고정하는 볼트
5 Nm (3.7 lbs-ft)
  • 10mm 소켓
  • 2인치 익스텐션
  • 래칫/토크 렌치
Reuse
LH 후면 캘리퍼를 LH 후면 너클에 고정하는 볼트
83 Nm (61.2 lbs-ft)
  • 외부 Torx E18
Replace
LH 후면 하프샤프트를 LH 후면 허브 어셈블리에 고정하는 너트
300 Nm (221.2 lbs-ft)
  • 32mm 딥 임팩트 소켓
  • 6인치 익스텐션
Replace

Remove

  1. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  2. LH 전면 도어를 열고 LH 전면 창문을 완전히 내립니다.
  3. EPB 정비 모드를 활성화합니다. 참조 항목: Parking Brake - Caliper - Rear - LH (Release).
  4. LH 후면 휠 중앙 캡이 장착되어 있는 경우 탈거합니다. 참조 항목: Cap - Wheel (Remove and Replace).
  5. LH 후면 휠 러그 너트를 풉니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Use only hand tools to remove or install the fasteners. Do not use impact or power tools.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Use a 6 point socket. Do not use a 12 point socket or a specialty socket.
  6. LH 후륜 구동 장치 하프샤프트 너트를 풉니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 긴 브레이커 바
    • 32mm 딥 임팩트 소켓
  7. LH 후면 휠을 탈거합니다. 참조 항목: Wheel Assembly (Remove and Install).
  8. LH 후면 캘리퍼를 LH 후면 너클에 고정하는 볼트를 탈거하여 폐기합니다. 너클에서 캘리퍼를 탈거한 다음, 캘리퍼가 S자형 후크에 걸려 있도록 둡니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E18
  9. LH 후면 하프샤프트 너트 및 와셔를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 32mm 딥 임팩트 소켓
    • 6인치 익스텐션
  10. 허브 풀러를 LH 후면 허브 어셈블리에 배치한 다음, 풀러를 휠 러그 너트(2개) 및 허브 풀러 와셔(2개)로 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 21mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 6인치 익스텐션
  11. 허브 풀러를 시계 반대 방향으로 회전하여 LH 후면 허브 스플라인에서 LH 후면 하프샤프트를 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 17mm 딥소켓
  12. LH 후면 허브 어셈블리에서 허브 풀러 공구를 탈거합니다.
  13. LH 후면 브레이크 로터를 허브에 고정하는 볼트를 탈거하되 로터를 아직 탈거하지 않습니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
    • 래칫/토크 렌치
  14. 차량에서 LH 후면 브레이크 로터를 탈거합니다.
  15. LH 후면 허브를 너클에 고정하는 볼트를 탈거한 다음, 차량에서 허브를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 18mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 3인치 익스텐션
    그림 1. 명확성을 위해 하프샤프트를 표시하지 않음

Install

  1. 장착하기 전에 LH 후면 허브의 톤 링을 검사합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    톤 링에 손상 징후가 보이면 교체합니다.
    그림 2. 불량 톤 링
    그림 3. 양호한 톤 링
  2. 약 1그램의 Molykote M-77 윤활 페이스트를 LH 후륜 구동 장치 하프샤프트의 외측 허브 접착면에만 도포합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하프샤프트 스플라인에는 윤활제를 도포하지 마십시오. 실수로 스플라인에 윤활제를 도포한 경우 작업용 타월로 닦아냅니다.
    그림 4. 빨간색으로 강조 표시한 영역 윤활
  3. LH 후면 하프샤프트를 LH 후면 허브 어셈블리에 배치한 다음, LH 후면 허브 및 베어링을 LH 후면 너클에 고정하는 볼트를 장착합니다.
    85 Nm (62.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 18mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 3인치 익스텐션
    그림 5. 명확성을 위해 하프샤프트를 표시하지 않음
  4. LH 후면 하프샤프트를 LH 후면 허브 어셈블리에 고정하는 새 노트 및 와셔를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    너트는 이후 단계에서 토크로 조입니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 32mm 딥 임팩트 소켓
    • 6인치 익스텐션
  5. LH 후면 브레이크 로터를 LH 후면 허브에 배치한 다음, 로터를 허브에 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
    • 래칫/토크 렌치
  6. LH 후면 캘리퍼를 LH 후면 너클에 배치한 다음, 캘리퍼를 너클에 고정하는 새 볼트를 장착합니다.
    83 Nm (61.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E18
  7. LH 후면 휠을 장착합니다. 참조 항목: Wheel Assembly (Remove and Install).
  8. LH 후면 하프샤프트 너트를 토크로 조입니다.
    300 Nm (221.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 32mm 딥 임팩트 소켓
  9. LH 전면 휠 중앙 캡이 장착되어 있던 경우 장착합니다. 참조 항목: Cap - Wheel (Remove and Replace).
  10. 차량 터치스크린에서 주차 버튼을 길게 눌러 EPB 정비 모드를 해제합니다.
  11. LH 전면 도어를 닫고 LH 전면 창문을 올립니다.
  12. 리프트에서 차량을 내립니다.
  13. Refer to the Alignment Requirement tables to determine whether an EPAS alignment check (EC) or four wheel alignment check (AC) is necessary. If performed, add the alignment check/adjust correction code as a separate activity to the SV. See 얼라인먼트 요구 사항 - 서스펜션.