2020-12-16

Hose - Washer - Reservoir (LHD) (Remove and Replace)

Correction code 17501512 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Hose - Washer - Reservoir (LHD) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
워터 탱크를 차량에 고정하는 볼트 및 너트
3 Nm (2.2 lbs-ft)
  • 10mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 6인치 익스텐션
Reuse

Remove

  1. LH 전면 도어를 열고 LH 전면 창문을 완전히 내립니다.
  2. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  3. LH 및 RH 와이퍼 암을 탈거합니다. Wiper Arms (Remove and Replace)을(를) 참조하십시오.
  4. 카울 스크린 패널을 탈거합니다. Panel - Cowl Screen (Remove and Replace)을(를) 참조하십시오.
  5. 윈드실드 워셔액 저장탱크 필러 넥을 탈거합니다. Filler Neck - Reservoir - Windshield Washer (LHD) (Remove and Replace)을(를) 참조하십시오.
  6. 와이퍼 모터를 탈거합니다. Wiper Module (Remove and Replace)을(를) 참조하십시오.
  7. 전기 하네스를 윈드실드 워셔액 탱크에 고정하는 클립을 분리합니다.
  8. 워터 탱크를 차량에 고정하는 볼트와 너트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 6인치 익스텐션
  9. 워셔액 탱크 레벨 센서를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    워셔액 탱크를 앞쪽으로 이동한 다음 위로 올려 레벨 센서 커넥터에 접근합니다.
  10. 원드실드 워셔 펌프 커넥터에서 전기 하네스를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    워셔액 탱크를 들어 올린 다음 시계 반대 방향으로 돌려 탱크 후면의 워셔 펌프에 접근합니다.
  11. 차량에서 윈드실드 워셔액 탱크를 탈거한 다음 탱크에서 워셔액을 회수합니다.
  12. 윈드실드 워셔액 탱크와 워셔 펌프에서 워셔 호스를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    워셔 펌프를 돌려 워셔 호스를 탈거합니다.

Install

  1. 윈드실드 워셔 호스를 윈드실드 워셔 펌프 및 탱크에 장착합니다.
  2. 전기 하네스를 윈드실드 워셔 펌프 커넥터와 레벨 센서 커넥터에 연결합니다.
  3. 차량에 윈드실드 워셔액 탱크를 장착한 다음, 윈드실드 워셔액 탱크를 차체에 고정하는 볼트와 너트를 장착합니다.
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 6인치 익스텐션
  4. 전기 하네스를 윈드실드 워셔액 탱크에 고정하는 클립을 조입니다.
  5. 와이퍼 모터를 장착합니다. Wiper Module (Remove and Replace)을(를) 참조하십시오.
  6. 윈드실드 워셔액 저장탱크 필러 넥을 장착합니다. Filler Neck - Reservoir - Windshield Washer (LHD) (Remove and Replace)을(를) 참조하십시오.
  7. 카울 스크린 패널을 장착합니다. Panel - Cowl Screen (Remove and Replace)을(를) 참조하십시오.
  8. LH 및 RH 와이퍼 암을 장착합니다. Wiper Arms (Remove and Replace)을(를) 참조하십시오.
  9. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  10. 윈드실드 워셔액 탱크에 워셔액을 채웁니다.
  11. 윈드실드 와이퍼 및 워셔의 작동을 확인합니다.