2026-11-02

차량 HV 비활성화 절차(7인승)

교정 코드 17010000 0.42 메모: 절차에서 명시적으로 언급하지 않는 한 교정 코드 및 해당 관련 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-11-26: Added note to keep HV gloves on if procedure that required disablement involves touching HV components.
  • 2024-12-20: Added note to set the clamp meter to measure DC.
  • 2024-06-05: Added warning to measure the specified order of locations for high voltage.
  • 2023-12-05: Updated references to other Vehicle Isolation Procedures.
  • 2023-11-08: Added/updated HV insulating glove steps.
  • 2023-05-02: Updated current measurement step sequence and consistency.
Warning
This procedure verifies that high voltage power is no longer available to high voltage components (A/C compressor, inverters, etc). Perform this procedure before servicing high voltage components.
Warning
고전압에 노출되는 절차를 수행하기 전에 작업자에게 모든 장신구(시계, 팔찌, 반지, 목걸이, 귀걸이, ID 태그, 피어싱 장신구 등)를 벗으라고 하고 주머니에서 모든 물건(열쇠, 동전, 펜, 연필, 공구, 패스너 등)을 꺼내 놓으십시오.
Warning
절차를 수행하기 위해서 시력 교정 안경이 필요한 경우, 시력 교정 안경을 머리에 단단히 고정하여 떨어지지 않게 하십시오.
Warning
Always wear High Voltage (HV) gloves and safety glasses when handling any high voltage component, including test equipment. Before each use, test gloves using an authorized glove tester and verify that the testing date on the gloves has not expired.
Warning
All repair and operating instructions should be reviewed and understood before working on Tesla vehicles, associated components, or associated repair equipment.
Warning
Assume that high voltage is present at all times when working on a Tesla vehicle, associated high voltage components, or associated high voltage test equipment until proven otherwise. Be aware that energy states can change during testing, so err on the side of caution.
Warning
Always have an electrical safety hook in the area when working with HV components. Electrical safety hooks are used to remove an injured person from a live high voltage circuit without risking additional injury.
Warning
Use a high voltage digital multimeter to check for the presence of high voltage on both sides of the connector every time a high voltage connector is disconnected. Do not use a
Warning
Make sure that the insulation meter and leads are capable of handling at least 500V DC.
Warning
Obey all instructions when using test equipment or servicing a Tesla vehicle or associated high voltage components. If repair instructions are not clear or if there are any questions about how to use the test equipment, escalate a Toolbox session before proceeding.
Warning
If any test equipment fails to operate as expected, do not attempt to diagnose or repair the vehicle. Follow the appropriate lock out – tag out procedure for the equipment, notify your manager.
Warning
When using test equipment, make sure that all cables are connected before turning equipment on or otherwise initiating use.
Warning
High voltage is present on battery recovery chargers whenever the HV LEDs are lit. However, indicators and LEDs can fail. Do not assume that if an LED is not lit no high voltage is present. Assume high voltage is present at all times until proven otherwise by use of a multimeter.
Warning

모든 필수 인증 교육을 완료한 기술자만 이 절차를 수행할 수 있습니다. Tesla는 타사 서비스 제공업체 기술자가 이 절차를 수행하기 전에 동등한 교육을 받을 것을 권장합니다. Tesla 기술자 요구 사항에 대한 자세한 내용이나 타사 기술자에 대한 분야별 설명은 HV Certification Requirements를 참조하십시오. 고전압 케이블, 버스바 또는 피팅을 다룰 때에는 항상 적합한 개인 보호 장비(PPE)와 클래스 0(1000V)의 최소 정격을 갖는 절연 HV 장갑을 착용해야 합니다. 추가 안전 정보는 기술 노트 TN-15-92-003고압 인식 주의 사항을 참조하십시오.

Equipment:
  • 1146175-00-A 전류 클램프, Fluke 374FC
  • 1130480-02-B Test Probes, Slim

Isolate

Note
This procedure is for 구조용 팩 이외 7 seat vehicles. For instructions on checking HV disablement on 구조용 팩 이외 5 seat vehicles, see 차량 HV 비활성화 절차. For instructions on checking HV disablement on 구조용 팩 5 seat vehicles, see 차량 HV 비활성화 절차 (구조용 팩)
  1. Open all the doors and lower all the windows.
  2. Remove the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
  3. Disconnect 12V/LV power. See 12V/LV 전원(연결 해제 및 연결).
  4. Set the current clamp to measure voltage , and then measure the voltage across the 12V/LV auxiliary battery terminals using the test probes.
    Note
    For LV (Li-Ion) auxiliary battery: if the voltage across the battery terminals is 0, the battery may have switched off internally. Use a 12V Lead Acid battery for testing. For mobile technicians: use the 12V Lead Acid battery in the Mobile Service vehicle.
    CAUTION
    For LV (Li-Ion) auxiliary battery: if the voltage across the battery terminals is less than 13 volts or greater than 16 volts, the current clamp is not measuring reliably and must not be used.
    CAUTION
    For 12V (Lead Acid) auxiliary battery: if the voltage measured is less than 10 volts or greater than 14 volts, the current clamp is not measuring reliably and must not be used.
  5. Remove the mid aero shield panel. See 패널 - 에어로 실드 - 후면(탈거 및 교체).
  6. Remove the rear battery skid plate. See 스키드 플레이트 - HV 배터리 - 후면(탈거 및 교체).
  7. Remove all items from pockets and ensure not wearing metal items.
  8. Inspect HV insulating gloves.
    Note
    Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves.
  9. Put on HV insulating gloves, leather outer gloves, and safety glasses.
    Warning
    Continue to wear the gloves until instructed to remove them.
  10. Power on the current clamp meter, and then zero out the meter for measurement.
    Warning
    Make sure to set the clamp meter to measure DC amps ("Adc").
  11. Install the current clamp meter onto one cable of the rear drive unit HV harness.
    Note
    Make sure the meter is facing the correct direction.
  12. Measure the current in the HV cable.
    • If the current is within the range of -0.5 A to 0.5 A, continue to the next step.
    • If the current is outside the range of -0.5 A to 0.5 A, for example -0.8 A or 1.3 A, re-perform the LV power disconnect procedure. See 12V/LV 전원(연결 해제 및 연결). If the measurement is still outside the range of -0.5 A to 0.5 A, escalate for assistance.
      Warning
      DO NOT DISCONNECT any HV harness when the current measurement is outside the range of -0.5 A to 0.5 A.
  13. Remove the nut that attaches the RDU HV cable bracket to the HV battery.
  14. Disconnect the RDU HV cable from the HV header.
    Note
    Release the locking tab, and then rotate the release lever upward to disengage the connector. Do not force the release lever up. Ensure the alignment tabs on the RDU header are not damaged.
  15. Verify no high voltage at the rear drive unit HV header.
    Warning
    잠재적 고전압 노출을 제한하기 위해 아래 지정된 순서에 따라 고전압을 측정하십시오.
    Note
    Verify test equipment is rated CATIII or higher. Measure B+ to Ground, B- to Ground, B+ to B-. If the voltage is greater than 10V, the pack contactors are not open or welded. Stop work and reach out to Service Engineering.
    Measurement Order

    Component Test

    B+

    (LH probe opening)

    B-

    (RH probe opening)

    GND

    Measured Voltage Less Than 10 V

    Measured Voltage 10 V Or More
    1

    HV battery positive contactor

    Positive (+) Lead

    Negative (-) Lead on screw that attaches the RDU HV header to the HV battery

    Pass

    Fail

    HV battery positive contactor might be seized. See HV 배터리 컨택터 소착 점검.
    2

    HV battery negative contactor

    Positive (+) Lead

    Negative (-) Lead on screw that attaches the RDU HV header to the HV battery

    Pass

    Fail

    HV battery negative contactor might be seized. See HV 배터리 컨택터 소착 점검.
    3

    HV

    Positive (+) Lead

    Negative (-) Lead

    Pass

    Fail

    Perform a HV battery contactor seize check. See HV 배터리 컨택터 소착 점검.
    Figure 1. B+ to GND measurement
    Figure 2. B- to GND measurment
    Figure 3. B+ to B- measurment
  16. Return to the procedure that required the vehicle to be electrically isolated.
    Warning
    차량을 전기 절연해야 하는 절차의 모든 안전 지침과 PPE 요구 사항을 따르십시오. 고전압 케이블, 버스바 또는 피팅을 다루는 절차의 경우 HV 장갑을 벗지 마십시오.
    Note
    If you are no longer exposed to high voltage, the HV insulating gloves may be removed.

Integrate

  1. If removed, put on the HV insulating gloves and leather over gloves.
  2. Connect the RDU HV cable to the HV battery.
    Note
    Make sure the connector lock is 90 degrees from the connector before beginning to secure the connector. Use one hand to support the connector while the other hand latches the locking tab. Once installed, verify that the latch is not damaged and fully secured in the latched position.
  3. Remove the leather glove protectors and the HV insulating gloves.
  4. Install the nut that attaches the RDU HV cable bracket to the HV battery.
    10 Nm (7.4 lbs-ft)
  5. Install the rear battery skid plate. See 스키드 플레이트 - HV 배터리 - 후면(탈거 및 교체).
  6. Install the mid aero shield panel. See 패널 - 에어로 실드 - 후면(탈거 및 교체).
  7. Connect 12V/LV power. See 12V/LV 전원(연결 해제 및 연결).
  8. Install the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
  9. Raise all the windows and close all the doors.