Towel Bar - 2nd Row Seat - LH (7-Seat) (Remove and Replace)
Correction code
13023702
0.78
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 개인 보호 to make sure wearing proper PPE when
performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
Remove
- Remove the LH 2nd row seat assembly from the vehicle. See Seat Assembly - 2nd Row - LH (7-Seat) (Remove and Replace).
-
Remove the push clip from the front of
the LH 2nd row seat outer sideshield assembly.
TIpUse a pick to remove the push clip from the bottom side of the outboard cover.
-
Release the clip that attaches the LH
2nd row seat outer sideshield to the seat assembly, disconnect the electrical connector,
and then remove the sideshield from the seat assembly.
참고Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
-
Release the clips (x3) that attach the
LH 2nd row seat inboard outer trim to the seat assembly, and then remove the trim from
the seat assembly.
- Remove the LH 2nd row seat toe kick cover. See Cover - Toe Kick - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
- Remove the LH 2nd row seat back panel. See Back Panel – 2nd Row Seat – LH (Remove and Replace).
- Remove the center 2nd row seat back panel. See Back Panel – 2nd Row Seat – Center/20 (5-Seat) (Remove and Replace).
-
Disconnect the LH 2nd row seat harness
electrical connectors (x7), and then release the clip that attaches the harness to the
seat frame.
-
Release the seat cables (x4) from the
LH 2nd row seat EZ entry actuator.
-
Remove the push clips (x2) from the LH
2nd row seat cushion pan.
- Remove the center 2nd row lumbar bun. See Lumbar Bun - 2nd Row - Center/20 (Remove and Replace).
- Remove the center 2nd row seat back pivot clamps. See Pivot Clamps - Seat Back - 2nd Row - Center/20 (Remove and Replace).
-
Lift the center 2nd row seat back
upward to remove it from the seat assembly.
-
Remove the fasteners (x4) that attach
the LH 2nd row seat seat pan to the seat frame.6 Nm (4.4 lbs-ft)1.5 Nm (1.1 lbs-ft)TIpUse of the following tool(s) is recommended:
- 10mm 소켓
- Torx T25 소켓
- Remove the LH 2nd row seat headrest trim. See Headrest - 2nd Row - Outer - LH (Remove and Replace).
-
Release the clips (x4) that attach the
LH 2nd row seat back to the seat assembly, and then lift the seat back to remove it from
the assembly.
- Remove the LH 2nd row headrest adjustment guide. See Adjustment Guide - Headrest - 2nd Row (Remove and Replace)
- Remove the LH 2nd row seat headrest guide lock. See Guide Lock - Headrest - 2nd Row (Remove and Replace).
-
Lift the rear of the LH 2nd row seat
cushion assembly, and then slide the cushion toward the front of the seat to remove it
from the seat assembly.
-
Use a pick to manually move the LH 2nd
row seat into easy entry position.
-
Remove and discard the bolts (x2) that
attach the LH 2nd row seat podium to the seat tracks.37 Nm (27.3 lbs-ft)TIpUse of the following tool(s) is recommended:
- 11mm 소켓
-
With one hand, engage the towel bar,
move the outer seat track rearward with the other hand until the groove on the LH seat
podium releases from the outer seat track, and then lift the LH 2nd row seat podium
upward while removing it from the inner seat track.
-
Release the clips (x2) that attach the
LH 2nd row EZ entry actuator cable to the RH easy entry latch, and then release the
cable from the latch.
-
Remove the nuts that attach the LH 2nd
row seat inner seat track to the seat frame assembly.37 Nm (27.3 lbs-ft)TIpUse of the following tool(s) is recommended:
- 13mm 소켓
-
Remove the LH 2nd row seat inner seat
track from the seat assembly.
참고Slide the outer seat track outwards away from the towel bar.
Install
-
Position the LH 2nd row seat inner seat track and towel bar into the seat
assembly.
참고Make sure the towel bar spring is in place and the bar is sitting between the tabs.
-
Install the nuts that attach the LH
2nd row seat inner seat track to the seat frame assembly.37 Nm (27.3 lbs-ft)참고Install outer seat track to seat frameTIpUse of the following tool(s) is recommended:
- 13mm 소켓
-
Secure the clips (x2) that attach the
LH 2nd row EZ entry actuator cable to the RH easy entry latch.
-
Install the groove on the LH 2nd row
seat podium to the inner seat track, and then align the groove on the podium to the
outer seat track. Engage the towel bar with one hand, and then move the outer seat track
inward until the groove on the podium engages to the seat track.
-
Install new the bolts (x2) that attach
the LH 2nd row seat podium to the seat tracks.37 Nm (27.3 lbs-ft)TIpUse of the following tool(s) is recommended:
- 11 mm socket
-
Position the LH 2nd row seat onto the
seat tracks, and then push the seat downward to latch the floor latches.
-
Starting at the rear of the seat,
position the LH 2nd row seat pan onto the seat frame.
-
Secure 60 seat bottom to seat
frame
참고4x fasteners, 3x 10mm, 6 Nm, 1x T25, 1.5 Nm, 1x clip, Install remaining bolts attaching seat pan to seat frame
-
Position the LH 2nd row seat back to
the seat assembly, and then install the clips (x4) that attach the seat back to the
assembly.
참고Make sure the bottom retainers slide into position.
- Install the LH 2nd row seat headrest guide lock. See Guide Lock - Headrest - 2nd Row (Remove and Replace).
- Install the LH 2nd row headrest adjustment guide. See Adjustment Guide - Headrest - 2nd Row (Remove and Replace).
- Install the LH 2nd row seat headrest trim. See Headrest - 2nd Row - Outer - LH (Remove and Replace).
- Install the center 2nd row seat back pivot clamps. See Pivot Clamps - Seat Back - 2nd Row - Center/20 (Remove and Replace).
- Install the center 2nd row lumbar bun. See Lumbar Bun - 2nd Row - Center/20 (Remove and Replace).
-
Position the LH 2nd row seat outer
sideshield to the seat assembly, connect the electrical connector, and then secure the
clip.
참고Release the outer sideshield assembly by pulling outwards and up at the front portion of the trim, and then releasing the remaining clip.
-
Install the push clip to the front of
the LH 2nd row seat outer sideshield assembly.
-
Install the clips (x3) that attach the
LH 2nd row seat inboard outer trim to the LH 2nd row seat.
- Install the center 2nd row seat back panel. See Back Panel – 2nd Row Seat – Center/20 (5-Seat) (Remove and Replace).
- Install the LH 2nd row seat toe kick cover. See Cover - Toe Kick - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
- Install the LH 2nd row seat back panel. See Back Panel – 2nd Row Seat – LH (Remove and Replace).
- Install the LH 2nd row seat assembly. See Seat Assembly - 2nd Row - LH (7-Seat) (Remove and Replace).