2024-08-27

Seat Assembly - 2nd Row - LH (7-Seat) (Remove and Replace)

Correction code 13050052 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-08-15: 북미 지역 차량용으로 어린이 잠금 장치용 ISOFIX 플래그가 없는 시트 커버는 교체해야 함을 알리는 참고 사항을 추가했습니다.

Torque Specifications

표 1. Torque Specifications: Seat Assembly - 2nd Row - LH (7-Seat) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 2열 시트 프레임을 차량에 고정하는 볼트(5개)
37 Nm (27.3 lbs-ft)
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 11mm 딥소켓
Replace

부품 번호: 1508763-00-A/B

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
볼트를 다음 순서에 따라 장착해야 합니다.
  1. 전면 외측
  2. 후면 내측
  3. 후면 외측
  4. 전면 안쪽

Remove

  1. LH 하단 C필러 트림을 탈거합니다. 참조 항목: Trim - C-Pillar - Lower - LH (7 Seat) (Remove and Replace).
  2. LH 2열 시트를 접어서 내립니다.
  3. LH 시트 프레임에서 로직 전기 커넥터를 연결 해제합니다.
  4. 2열 LH 시트를 앞으로 이동합니다.
  5. LH 2열 시트 프레임을 차량에 고정하는 볼트(5개)를 탈거하여 폐기합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 11mm 딥소켓
  6. LH 2열 시트를 완전히 뒤쪽으로 이동합니다.
  7. LH 2열 시트 외측 트랙 커버를 탈거합니다. 참조 항목: Cover - Seat Track - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
  8. LH 2열 시트 중앙 트랙 커버를 탈거합니다. 참조 항목: Cover - Seat Track - 2nd Row Seat - Center (7-Seat) (Remove and Replace).
  9. 실내 카펫을 차량 전면을 향해 당겨 LH 2열 시트에서 분리합니다.
  10. 보조 작업자와 함께 LH 2열 시트 어셈블리를 차량에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    For NA only: If the 2nd row seat that is not being replaced does not have ISOFIX flag for child locks, replace the seat cover. 참조 항목: Cover - Seat Back - 2nd Row - LH (7-Seat) (Remove and Replace).

Install

  1. 보조 작업자와 함께 LH 2열 시트 어셈블리를 차량에 배치합니다.
  2. LH 2열 시트 프레임에 로직 전기 커넥터를 연결합니다.
  3. LH 2열 시트 프레임을 차량에 고정하는 새 볼트(5개)를 장착합니다.
    37 Nm (27.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    다음의 순서대로 규격 토크로 조입니다.
    1. 전면 외측
    2. 후면 내측
    3. 후면 외측
    4. 전면 내측
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 11mm 딥소켓
  4. 실내 카펫을 제자리에 배치한 다음 벨크로를 고정합니다.
  5. LH 2열 시트를 수직으로 접습니다.
  6. LH 2열 시트 외측 트랙 커버를 장착합니다. 참조 항목: Cover - Seat Track - 2nd Row Seat - LH (7-Seat) (Remove and Replace).
  7. LH 2열 시트 중앙 트랙 커버를 장착합니다. 참조 항목: Cover - Seat Track - 2nd Row Seat - Center (7-Seat) (Remove and Replace).
  8. LH 하단 C필러 트림을 장착합니다. 참조 항목: Trim - C-Pillar - Lower - LH (7 Seat) (Remove and Replace).
  9. Toolbox가 설치된 노트북을 차량에 연결합니다.
  10. Toolbox에서 Actions/Autodiag를 클릭한 다음 "ENABLE_PITCH"를 검색합니다.
  11. 전면 시트를 원래 위치로 이동합니다.
  12. 모든 창문을 올리고 모든 도어를 닫습니다.