2024-10-28

Light - Brake - Center High Mounted (Remove and Replace)

Correction code 17402502 1.50 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
For Europe only: Only technicians who have been trained in working with diisocyanates and have completed all required certification courses are permitted to perform procedures using urethane and other products containing diisocyanates. Proper personal protective equipment (PPE) must be worn when working with products containing diisocyanates.

Remove

  1. 백라이트 글라스를 탈거합니다. 참조 항목: 글라스 - 백라이트(탈거 및 장착).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    이 절차를 수행할 때는 새 CHMSL을 나중에 기존 백라이트 글라스에 장착할 수 있도록 백라이트 글라스 상단의 H 클립이 파손되지 않도록 하십시오.
  2. CHMSL 어셈블리의 클립 2개를 눌러 백라이트 글라스에서 탈거합니다.
  3. 날개 스크래퍼 세트를 사용하여 백라이트 어셈블리에서 남은 우레탄을 제거합니다.
  4. 로케이터(2개) 영역에서 양면 테이프 잔여물을 제거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 이레이저 휠
    • 배터리 구동식 드릴 - 1126456-00-A
    • 날개 스크래퍼 세트 - 1080601-00-A
  5. 모든 스페이서 패드(11개)를 탈거합니다.
  6. 날개 스크래퍼 세트를 사용하여 리프트게이트 차체에서 남은 우레탄을 제거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    우레탄 잔여물 두께가 1mm 이하인지 확인합니다.
  7. 모든 결합면을 이소프로필 알코올(IPA) 천으로 닦습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    CHMSL에서 눈에 보이는 지문 또는 표시를 제거합니다.

Install

  1. 로케이터(2개)를 백라이트 글라스에 장착합니다.
  2. 모든 스페이서 패드(11개)를 백라이트 글라스에 장착합니다.
  3. CHMSL 어셈블리를 백라이트 글라스에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    제자리에 고정될 때까지 CHMSL을 양쪽 H 클립에 고르게 밀어 넣습니다.
  4. 백라이트 글라스를 장착합니다. 참조 항목: 글라스 - 백라이트(탈거 및 장착).