2025-06-27

Brake Rotor - Rear - LH (Remove and Replace)

Correction code 33010202 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2025-05-08: 로터 교체 후 수행해야 하는 브레이크 패드 버니싱 단계를 업데이트했습니다.
  • 2024-05-28: 참조 및 주의 사항을 업데이트했습니다.
  • 2023-11-22: 싱글 로터 교체에 대한 별도의 정보를 추가했습니다.
  • 2023-06-15: 캘리퍼 스프레더를 사용하여 수동으로 피스톤을 캘리퍼로 밀어넣는 단계를 추가하였고 브레이크 패드 버니싱으로 별도로 교정 코드 33013000을 추가해야 함을 다시 알려주는 노트를 추가했습니다.
  • 2023-06-15: 보충 목적 전용으로 전체 절차 비디오를 개요로 추가했습니다.
  • 1109954-00-A 브레이크 캘리퍼 스프레더
Informational PurposesAn informational icon, calling your attention
참고
자세한 브레이크 규격은 브레이크의 내용을 참조하십시오.
Informational PurposesAn informational icon, calling your attention
참고
싱글 로터 교체가(파손으로 인해) 필요한 경우, 해당 액슬 로터는 반드시 런아웃 및 두께를 측정해야 합니다. Brake Rotor - Rear - LH (Measure Runout)을(를) 참조하십시오.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Torque Specifications

http://service.tesla.com/user/documents 테스트
표 1. 토크 규격: 브레이크 로터 - 후면 - LH
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 후면 캘리퍼에서 LH 후면 너클
83 Nm (61.2 lbs-ft)
  • 외부 Torx E18
  • 래칫/토크 렌치
Replace
브레이크 로터에서 허브
5 Nm (3.7 lbs-ft)
  • 10mm 소켓
  • 2인치 익스텐션
  • 래칫/토크 렌치
Reuse

Remove

  1. 차량을 들어 올려서 LH 후면 휠을 탈거합니다. Wheel Assembly (Remove and Install)을(를) 참조하십시오.
  2. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  3. LH 후면 캘리퍼를 LH 후면 너클에 고정하는 볼트를 탈거하여 폐기하고 너클에서 캘리퍼를 탈거한 다음 캘리퍼를 S자형 후크에 겁니다.
    83 Nm (61.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 외부 Torx E18
    • 래칫/토크 렌치
  4. 캘리퍼 스프레더 도구를 사용하여 캘리퍼 피스톤을 완전 개방 위치로 밉니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    이는 새 브레이크 패드를 장착할 때 더 많은 간격을 확보해 줍니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    피스톤 상단 절단부가 두 탭 가운데 위치하도록 하십시오.
  5. 브레이크 로터를 허브에 고정하는 볼트를 탈거한 다음 허브에서 브레이크 로터를 탈거합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    초기 생산 차량에는 브레이크 로터를 허브에 고정하는 볼트가 장착되어 있지 않을 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
    • 래칫/토크 렌치

Install

Installation procedure is the reverse of removal, except for the following:

  1. Replace all patchbolts.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    To prevent damage to the flexible brake hose, make sure that the brake hose is not twisted and can bend forward and does not make contact with the wheel arch liner when the vehicle is lowered.
  2. EPB 정비 모드를 종료하려면 차량을 주차로 두고 주차 브레이크를 작동합니다.
  3. 브레이크 페달을 5회 이상 밟아 패드가 로터에 안착되게 합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    차량을 주행하기 전에 항상 브레이크 패드가 올바르게 안착되었는지 확인하십시오.
  4. 브레이크를 버니싱합니다. 참조 항목: Brake Pads - Burnishing.
    Informational PurposesAn informational icon, calling your attention
    참고
    차량 주행 시, 적절한 브레이크 페달의 느낌과 성능이 달성되었는지 확인하십시오.
    Informational PurposesAn informational icon, calling your attention
    참고
    서비스 방문에 브레이크 패드 버니싱 교정 코드 33013000를 별도 활동으로 추가합니다.