교정 코드 16102120 0.65 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

1. Open all four doors
2. Lower all four windows
3. Open hood
4. Remove rear apron
   참고

   14x clips

   

   

5. Remove bolt securing frunk to washer fluid reservoir neck
   참고

   1x bolt, 10mm, 5 Nm

   

6. Release washer tank neck from washer tank and set aside
   참고

   1x O-ring, No need to remove hose from neck

   

   

7. Remove HEPA filter assembly
   참고

   2x bolts, 10mm, 5 Nm, Pivot rearward edge up and past brake reservoir, then lift up to clear frunk assembly

   

   

   

8. Move LH front seat forward
9. Move RH front seat forward
10. Remove 2nd row seat cushion
    참고

    1x connector, Lift front edge of seat cushion upward to release foam from frame

    

    

    

11. Raise and support vehicle
    참고

    Ensure vehicle is not charging, Note the MYSP lifting points are more narrow than the MY

    

    

    

    

12. Power off vehicle from center display
    참고

    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
13. Disconnect LV battery connector and First Responder Loop
    참고

    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

    

14. Verify operation of multimeter
    참고

    Set multimeter to DC voltage, Confirm multimeter is properly measuring voltage by testing LV battery, Touch lightly and do not damage terminals

    

    

15. Raise vehicle fully and lower lift onto locks
    참고

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
16. Remove push clips at left and right wheel house liner to mid aero shield
    참고

    2x clips

    

    

17. Remove mid aero shield
    참고

    11x bolts, 10mm, 5 Nm, Fasteners may vary, MYSP will have one less bolt and an extra clip

    

18. Remove all items from pockets and ensure not wearing metal items

    

    

19. Inspect HV insulating gloves
    참고

    Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves. https://service.teslamotors.com/protected-doc/ServiceBulletins/External/TN/TN-15-92-003_High_Voltage_Awareness_Care_Points_R4.pdf

    

20. Put on HV insulating gloves and leather over gloves
    참고

    Make sure to wear Electrical Protective Gloves any time Hioki tester is used

    

21. Install amp clamp to RDU HV harness
    참고

    Verify meter is zeroed out before performing measurement, Measure single cable. Verify ammeter is installed in correct direction. If current > 0.5A do not proceed with disconnecting HV connector. In this case, start vehicle electrical isolation again to make sure that all was properly shut down. Escalate for assistance as requiredIf current < 0.5A, Ok to disconnect and check voltage at HV plug on the battery side.

    

    

    

22. Release RDU HV harness from HV battery
    참고

    1x connector, Release locking tab and rotate the release lever up to disengage the connector, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damaged

    

23. Verify no high voltage at RDU HV header
    참고

    Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering

    

    

    

    

24. Remove HV insulating gloves
25. Remove breather plugs from thermal vents
    참고

    4x plugs, 3x tabs per plug, Discard after removal

    

    

26. Install air splitter hoses onto thermal vents
    참고

    5x hoses, Splitter still in development

    

    

    

    

    

27. Lower vehicle partially and set lift onto locks
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
28. Cut away insulation covering pyro cover
    참고

    If insulation is present then cut away

    

29. Remove breather from pyro cover
    참고

    1x breather, Discard after removal

    

30. Install air splitter hose onto pyro cover
    참고

    1x hose, Splitter still in development

    

    

31. Close both valves on the regulator test tool

    

32. Connect regulator to air supply

    

33. Turn right side regulator valve to the open position
    참고

    By turning the valve knob to a horizontal position, The valve is fully open

    

34. Set regulator to 0.3 psi

    

35. Open left side regulator valve to inject air into ancillary bay
    참고

    Allow 50 seconds fill time, Close right side regulator valve when pressure reaches 0.3 psi

    

    

    

36. Wait 30 seconds for pressure to settle
37. Record value of starting pressure
38. Wait 60 seconds to test pressure
39. Record value of end pressure
    참고

    Subtract ending pressure from starting pressure, If difference is greater than 0.08143 psi then inspect tools and retest, If difference is still greater than 0.08143 psi then escalate a Toolbox session, If difference is 0.08143 psi or less then proceed with current procedure
40. Disconnect air supply from regulator tool

    

41. Remove air splitter hose from pyro cover
    참고

    1x hose, Splitter still in development

    

42. Install breather onto pyro cover
    참고

    1x breather, Install new breather

    

43. Raise vehicle fully and lower lift onto locks
    참고

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
44. Disconnect enclosure leak tester from air splitter

    

45. Remove air splitter hoses from thermal vents
    참고

    5x hoses, Splitter still in development

    

    

    

    

    

46. Install breather plugs onto thermal vents
    참고

    4x plugs, 3x tabs per plug, Install new plugs, Press plug evenly, Make sure tabs are fully engaged and plug is flush with vent

    

    

    

47. Secure RDU HV harness onto HV battery
    참고

    1x connector, Verify lever is in the upright and open position, Carefully seat connector and allow lever to engage, Fully secure lever and verify red tab is locked, Do not damage any pins

    

48. Apply Loctite 222 onto mid aero shield bolts and install mid aero shield
    참고

    11x bolts, 10mm, 5 Nm, Fasteners may vary, Model Y Structural Pack will one less bolt and one extra clip

    

49. Install push clips at left and right wheel house liner to mid aero shield
    참고

    2x clips

    

    

50. Lower vehicle fully
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
51. Connect first responder loop and LV battery
    참고

    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

    

    

    

52. Install HEPA filter assembly
    참고

    2x bolts, 10mm, 5 Nm, Pivot forward edge down past frunk assembly, then carefully move rear edge past brake reservoir and into position

    

    

    

53. Secure washer tank neck onto washer tank
    참고

    1x O-ring, Ensure washer hose is properly routed

    

54. Install bolt securing frunk to washer fluid reservoir neck
    참고

    1x bolt, 10mm, 5 Nm

    

55. Install rear apron
    참고

    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips

    

    

56. Close hood
57. Install 2nd row seat cushion
    참고

    1x connector, Slide rear cushion rearward then align foam with seat rail, Make sure cushion is fully seated with push & pull test

    

    

    

58. Move LH front seat to original position
59. Move RH front seat to original position
60. Remove vehicle from lift
    참고

    Lower rack arms fully and remove from under vehicle
61. Raise all four windows
62. Close all four doors
    참고

    If 12V is powered up, Unlatch rear doors before closing