2021-11-11

Podium - Seat - Driver (Remove and Replace)

Correction code 13012412 1.20 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.

Remove

  1. 후면 후드 내 에이프런을 탈거합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.
  2. 12V 전원을 연결 해제합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  3. 운전석 시트를 탈거합니다. Seat Assembly - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  4. 전면 동승석 시트를 탈거합니다. Seat Assembly - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  5. 센터콘솔을 탈거합니다. Center Console (Remove and Install)을(를) 참조하십시오.
  6. 2열 하단 시트 쿠션을 탈거합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  7. LH 및 RH 하단 B필러 트림을 탈거합니다. Trim - B-Pillar - Lower - LH (Non-Structural Pack) (Remove and Replace)을(를) 참조하십시오.
  8. 후면 카펫을 탈거합니다. Carpet - Rear (Remove and Replace)을(를) 참조하십시오.
  9. LH 전면 카펫을 탈거합니다. Carpet - Front - LH (Remove and Replace)을(를) 참조하십시오.
  10. RH 전면 카펫을 탈거합니다. Carpet - Front - RH (Remove and Replace)을(를) 참조하십시오.
  11. 1열 시트 포디엄 어셈블리 후면에서 하네스 클립을 연결 해제합니다.
  12. 1열 시트 포디엄 어셈블리를 차량에 고정하는 볼트(4개)를 탈거하여 폐기한 다음 차량에서 포디엄을 탈거합니다.
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 도구 사용을 권장합니다.
    • 11mm 딥소켓
    • 4인치 익스텐션

Install

  1. 1열 시트 포디엄 어셈블리를 차량에 배치한 다음 포디엄 어셈블리를 차량에 고정하는 새 볼트(4개)를 장착합니다.
    33.5 Nm (24.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 도구 사용을 권장합니다.
    • 11mm 딥소켓
    • 4인치 익스텐션
  2. 하네스 클립을 1열 시트 포디엄 어셈블리 후면에 장착합니다.
  3. RH 전면 카펫을 장착합니다. Carpet - Front - RH (Remove and Replace)을(를) 참조하십시오.
  4. LH 전면 카펫을 장착합니다. Carpet - Front - LH (Remove and Replace)을(를) 참조하십시오.
  5. 후면 카펫을 장착합니다. Carpet - Rear (Remove and Replace)을(를) 참조하십시오.
  6. LH 및 RH 하단 B필러 트림을 장착합니다. Trim - B-Pillar - Lower - LH (Non-Structural Pack) (Remove and Replace)을(를) 참조하십시오.
  7. 2열 하단 시트 쿠션을 장착합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  8. 센터콘솔을 장착합니다. Center Console (Remove and Install)을(를) 참조하십시오.
  9. 전면 동승석 시트를 장착합니다. Seat Assembly - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  10. 운전석 시트를 장착합니다. Seat Assembly - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  11. 12V 전원을 연결합니다. 12V/LV Power (Disconnect and Connect)을(를) 참조하십시오.
  12. 후면 후드 내 에이프런을 장착합니다. Underhood Apron - Rear (Remove and Replace)을(를) 참조하십시오.