2021-06-09

Cover - Front - Seat Track - 1st Row Seat (Remove and Replace)

Correction code 13011812 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 모든 도어를 열고 모든 창문을 완전히 내립니다.
  2. 운전석을 완전히 앞으로 이동합니다.
  3. 운전석 시트의 후면을 차체에 고정하는 볼트(2개)를 탈거하여 폐기합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 3/8인치 표준 플렉스 헤드 래칫
    • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
  4. 운전석 시트를 완전히 뒤로 이동합니다.
  5. 운전석 시트의 전면을 차체에 고정하는 볼트(2개)를 탈거하여 폐기합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • Trox Plus T45 소켓
    • 3/8인치 표준 플렉스 헤드 래칫
    • 3/8인치 플렉스 헤드 토크 렌치(장착 전용)
  6. 운전석 시트를 위로 들어 올린 다음 트랙 커버를 앞으로 밀어 시트 어셈블리에서 탈거합니다.

Install

  1. 시트 트랙 커버를 차량에 장착합니다.
  2. 운전석 시트를 완전히 뒤로 이동합니다.
  3. 새 볼트(2개)를 장착하여 운전석 시트 앞쪽을 차체에 고정합니다.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 조입니다.
  4. 운전석을 완전히 전방으로 이동합니다.
  5. 새 볼트(2개)를 장착하여 운전석 시트 뒤쪽을 차체에 고정합니다.
    33.5 Nm (24.7 lbs-ft)
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Torx Plus T45 비트만 사용하여 시트 볼트를 조입니다.
  6. 운전석 시트를 원래 위치로 이동합니다.
  7. 모든 창문을 올리고 모든 도어를 닫습니다.