2025-06-27

Charge Port (NACS) (Remove and Replace)

Correction code 44011602 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-10-27: 차체 쪽 충전 포트(CP) 볼트 토크를 9Nm으로 업데이트합니다.
  • 2023-10-10: 충전 포트 도어를 수동으로 닫지 않도록 하라는 주의 사항을 추가했습니다.
  • 1076921-00-B 절연 멀티미터, Fluke 1507(북미)
  • 1076921-00-A 절연 멀티미터, Fluke 1587(유럽/중동/아프리카)
  • 1076921-01-B 절연 멀티미터, Fluke 1508(아시아 태평양)
  • 1076927-00-A Hioki RM 3548
  • 1130480-00-A 테스트 프로브, 슬림 타입, Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

이 절차를 수행하려면 적합한 개인 보호 장비(PPE)가 필요합니다.

  • 고전압 절연 장갑
  • 가죽 장갑 보호구
  • 고전압 장갑 테스터
  • 보안경
  • 전기 위험 등급 안전 장화
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Make sure that the HV gloves are not expired.
  • North America: HV gloves can be used up to 12 months after the testing date printed on the glove, but only 6 months after first use even if the gloves are still within the 12 month period. If the gloves were not put into service during the 12-month period following the testing date, they must be retested before being put into service.
  • Europe: Class 0 (1000V) HV gloves have no expiration date and may be used if they pass the pre-use assessment and the periodic inspection.
  • Asia Pacific: Follow the expiration date stated by the HV glove manufacturer, and:
    • o China only: Test the gloves every 6 months according to GB/T 17622.

Torque Specifications

표 1. Torque Specifications: Charge Port (NACS) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
충전 포트(CP)를 차체에 고정하는 볼트
9 Nm (6.6 lbs-ft)
  • 10mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
버스바를 충전 포트(CP)에 고정하는 너트
9 Nm (6.6 lbs-ft)
  • 10mm 딥소켓
  • ¼인치 표준 플렉스 헤드 래칫
  • ¼인치 토크 렌치(장착 전용)
Reuse

Remove

  1. 모든 창문을 내립니다.
  2. 모든 도어를 열고 후면 도어를 걸쇠로 고정합니다.
  3. 운전석 시트 및 전면 동승석 시트를 완전히 앞으로 이동합니다.
  4. 리프트게이트를 엽니다.
  5. 후드를 엽니다.
  6. 충전 포트 도어를 엽니다.
  7. 12V 전원을 분리합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  8. 충전 포트(CP) 전압 점검 절차를 수행합니다. 참조 항목: Charge Port Voltage Check.
  9. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  10. 2열 하단 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  11. LH 하단 C필러 트림을 탈거합니다. 참조 항목: Trim - C-Pillar - Lower - LH (Remove and Replace).
  12. 후면 트렁크 바닥 트림을 탈거합니다. 참조 항목: Trunk Load Floor - Rear (Remove and Replace).
  13. 전면 트렁크 플로어 트림을 탈거합니다. 참조 항목: Trunk Load Floor - Front (Remove and Replace).
  14. 트러크 씰 트림을 탈거합니다. 참조 항목: Trim - Sill - Trunk (Remove and Replace).
  15. LH 트렁크 로드 플로어 브래킷을 탈거합니다. 참조 항목: Bracket - Trunk Load Floor - LH (Remove and Replace).
  16. LH 트렁크 포켓 브래킷을 탈거합니다. 참조 항목: Bracket - Trunk Pocket - LH (Remove and Replace).
  17. LH 트렁크 사이드 트림을 탈거합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  18. LH 상단 C필러 트림을 차량에 고정하는 클립(6개) 및 탭(1개)을 분리한 다음 트림을 한쪽으로 치워 둡니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    헤드라이너에서 LH 상단 C필러 트림의 최전방을 주의하여 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    LH 상단 C필러 트림은 후면 안전벨트에 여전히 고정되어 있습니다.
  19. C필러 브래킷을 탈거합니다. 참조 항목: Bracket - C-Pillar - LH (Remove and Replace).
  20. 충전 포트 ECU에서 LH 차체 하네스 커넥터(2개)를 연결 해제합니다.
  21. LH 차체 하네스를 차량에 고정하는 클립을 풉니다.
  22. 충전 포트 저전압 커넥터(2개)에서 잠금 탭을 분리한 다음 충전 포트(CP)에서 커넥터(2개)를 연결 해제합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    검은색 커넥터 탭을 부드럽게 들어 올려 12핀 저전압 커넥터에서 하얀색 잠금 탭을 탈거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  23. 충전 포트 어셈블리에서 충전 포트 버스바 패스너 커버를 탈거합니다.
  24. 충전 포트 버스바를 충전 포트(CP)에 고정하는 너트를 탈거한 다음 버스바를 충전 포트 스터드에서 밀어 빼냅니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • ¼인치 표준 플렉스 헤드 래칫
    • ¼인치 토크 렌치(장착 전용)
  25. 충전 포트(CP)를 차체에 고정하는 볼트를 탈거한 다음 충전 포트(CP)를 차량에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

Install

  1. 나중에 이 절차에서 저항을 측정하는 것에 대비하여 Hioki 저항계의 영점 조정을 수행합니다. 참조 항목: Resistance Meter (Zero Adjust)
  2. 동일한 충전 포트(CP)를 다시 장착하는 경우 충전 포트 어셈블리 후면의 충전 포트 버스바 HV 헤더를 IPA 천으로 닦은 다음 1분 동안 자연 건조시킵니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트(CP)에 전기 접합부 컴파운드가 미리 도포되어 있으므로, 새 충전 포트 어셈블리를 장착할 경우 이 단계를 건너뜁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    플라스틱 트림 공구를 사용하여 IPA 천을 충전 포트 버스바 HV 헤더의 틈새에 밀어 넣습니다.
  3. 충전 포트(CP)를 차량에 배치한 다음 충전 포트를 차체에 고정하는 볼트를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하네스가 제대로 배선되었는지 확인하고, 케이블타이가 있는 접착 패드가 장착된 경우 올바르게 장착되어 있는지 확인합니다.
  4. 동일한 충전 포트(CP)를 다시 장착하는 경우: 충전 포트 뒤쪽 버스바 스터드의 토크 점검을 수행합니다.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트(CP) 어셈블리를 장착하는 경우 이 단계를 건너뜁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 비트
    • 4인치 익스텐션
    • 래칫/토크 렌치
  5. IPA 천을 사용하여 충전 포트 버스바 리드에서 잔류물 및 잔해를 모두 닦은 다음 1분 동안 자연 건조시킵니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
  6. 동일한 충전 포트(CP)를 다시 장착하는 경우 각 충전 포트 버스바 리드에서 충전 포트(CP)와 접촉하는 면에 Penetrox A-13 전기 접합부 컴파운드를 한 방울씩 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트(CP)에 전기 접합부 컴파운드가 미리 도포되어 있으므로, 새 충전 포트 어셈블리를 장착할 경우 이 단계를 건너뜁니다.
  7. 충전 포트 버스바를 충전 포트 스터드에 배치한 다음 버스바를 충전 포트(CP)에 고정하는 너트를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • ¼인치 표준 플렉스 헤드 래칫
    • ¼인치 토크 렌치(장착 전용)
  8. HV 절연 장갑과 가죽을 덧댄 장갑을 착용합니다.
  9. 충전 포트(CP)에서 Hioki 저항계를 사용하여 충전 포트 버스바 리드와 충전 포트 버스바 스터드 사이의 저항을 측정합니다. 다른 리드 및 스터드에서도 이 테스트를 수행합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    허용 가능한 저항은 0.050mΩ(50μΩ)~0.270mΩ(270μΩ)입니다. 측정된 저항이 270mΩ(270μΩ)을 초과하면 고전압 조인트에 저항이 너무 많은 것입니다. 필요에 따라 패스너를 탈거하고 이소프로필 알코올로 해당 부위를 청소한 후 패스너를 다시 장착하고 다시 테스트합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    저항이 0.050mΩ(50μΩ) 미만일 때에는 프로브를 재배치하고 다시 측정합니다. 4회 시도 후 저항이 일정하게 0.050mΩ(50μΩ) 미만이면 테스트가 통과한 것이므로 다음 단계를 계속합니다.
  10. HV 절연 장갑과 가죽을 덧댄 장갑을 벗습니다.
  11. 충전 포트 어셈블리에 충전 포트 버스바 패스너 커버를 장착합니다.
  12. 충전 포트 저전압 커넥터(2개)를 충전 포트(CP)에 장착한 다음 잠금 탭을 양쪽 커넥터에 체결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Push the red locking tab into the connector to engage the connector lock.
    Informational PurposesAn informational icon, calling your attention
    TIp
    하얀색 잠금 탭이 검은색 커넥터 탭에 잠길 때까지 12핀 저전압 커넥터에 주의하여 삽입합니다.
  13. LH 차체 하네스를 차량에 고정하는 클립을 장착합니다.
  14. LH 차체 하네스 커넥터(2개)를 충전 포트 ECU에 연결합니다.
  15. C필러 브래킷을 장착합니다. 참조 항목: Bracket - C-Pillar - LH (Remove and Replace).
  16. LH 상단 C필러 트림을 차량에 배치한 다음 트림을 차량에 고정하는 클립(6개) 및 탭(1개)을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    C필러 트림 전면부의 상단 그루브를 헤드라이너와 정렬합니다.
  17. LH 트렁크 사이드 트림을 장착합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  18. LH 트렁크 포켓 브래킷을 장착합니다. 참조 항목: Bracket - Trunk Pocket - LH (Remove and Replace).
  19. LH 적재함 바닥 브래킷을 장착합니다. 참조 항목: Bracket - Trunk Load Floor - LH (Remove and Replace).
  20. 트렁크 씰 트림을 장착합니다. 참조 항목: Trim - Sill - Trunk (Remove and Replace).
  21. 전면 트렁크 플로어 트림을 장착합니다. 참조 항목: Trunk Load Floor - Front (Remove and Replace).
  22. 후면 트렁크 바닥 트림을 장착합니다. 참조 항목: Trunk Load Floor - Rear (Remove and Replace).
  23. LH 하단 C필러 트림을 장착합니다. 참조 항목: Trim - C-Pillar - Lower - LH (Remove and Replace).
  24. 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  25. 12V 전원을 다시 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  26. 리프트게이트를 닫습니다.
  27. 충전 포트 도어를 닫습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    충전 포트 도어를 수동으로 닫지 않도록 하십시오.
  28. 운전석 및 전면 동승석을 이전 위치로 되돌립니다.
  29. 래치를 풀고 모든 도어를 닫습니다.