2024-10-15

Decor Trim - Instrument Panel - Main (Remove and Replace)

Correction code 14057002 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-12-25: 조명이 켜지는 계기판 장식 트림을 위한 단계가 추가되었습니다.
표 1. Torque Specifications: Decor Trim - Instrument Panel - Main (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
주 장식 트림을 계기판의 LH 및 RH에 고정하는 나사
2.3 Nm (1.7 lbs-ft)
  • Torx T20 소켓
  • 4인치 익스텐션
  • 래칫/토크 렌치
Reuse

Remove (조명이 없는 장식 트림의 경우)

  1. LH 및 RH 계기판 엔드캡을 탈거합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  2. LH 및 RH 에어 웨이브 엔드캡을 탈거합니다. 참조 항목: End Cap - Air Wave - LH (Remove and Replace).
  3. 해당하는 경우 주 장식 트림을 계기판의 LH 및 RH 쪽에 고정하는 나사(2개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 4인치 익스텐션
    • 래칫/토크 렌치
  4. 주 계기판 장식 트림을 고정하는 클립(15개)을 분리한 다음 계기판에서 트림을 탈거합니다.

Remove (조명이 켜지는 장식 트림의 경우)

  1. LH 및 RH 계기판 엔드캡을 탈거합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).
  2. 주 계기판 장식 트림을 고정하는 커넥터(2개), 클립(7개), 하네스 고정 브래킷(3개), 매직 테이프(6개)를 풀거나 떼어낸 다음 트림을 계기판에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    왼쪽 커넥터를 연결 해제하기 전에 커넥터에서 차단재를 탈거하십시오. 고정 클립은 필요에 따라 교체합니다.

Install (조명이 없는 장식 트림의 경우)

  1. 주 계기판 장식 트림을 계기판에 고정하는 클립(15개)을 장착합니다.
  2. 해당하는 경우 주 장식 트림을 계기판의 LH 및 RH에 고정하는 나사(2개)를 장착합니다.
    2.3 Nm (1.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 4인치 익스텐션
    • 래칫/토크 렌치
  3. LH 및 RH 에어 웨이브 엔드캡을 장착합니다. 참조 항목: End Cap - Air Wave - LH (Remove and Replace).
  4. LH 및 RH 계기판 엔드캡을 장착합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).

Install (조명이 켜지는 장식 트림의 경우)

  1. 주 계기판 장식 트림을 계기판에 부착하는 커넥터(2개), 클립(7개), 하네스 고정 브래킷(3개), 매직 테이프(6개)를 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    고정 클립은 필요에 따라 교체합니다.
  2. TEST-SELF_VCLEFT_RGB-NIFFLERvia Toolbox: (link) 루틴을 수행합니다.
    1. Toolbox 3가 설치된 노트북을 차량에 로컬로 연결합니다. 참조 항목: Toolbox 3(연결 및 연결 해제).
    2. Actions 탭에서 TEST-SELF_VCLEFT_RGB-NIFFLERvia Toolbox: (link)을(를) 검색하고 TEST-SELF_VCLEFT_RGB-NIFFLERvia Toolbox: (link)을(를) 선택한 다음 Run을 클릭하여 루틴이 완료될 때까지 기다립니다.
    3. 노트북을 연결 해제합니다.
    4. 정비 모드를 비활성화합니다. 참조 항목: Service Mode.
  3. LH 및 RH 계기판 엔드캡을 장착합니다. 참조 항목: End Cap - Instrument Panel - LH (Remove and Replace).