14/10/2022 00:04:46

오일 펌프 - 후륜 구동 장치(4DU)(탈거 및 교체)

교정 코드 40304642 0.54 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT에 대한 자세한 내용과 FRT가 만들어진 방법은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 검증되었지만 초안입니다. 경고와 주의사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.

탈거

  1. Move the vehicle to a 2 post lift. See 차량 올리기 - 2 포스트 리프트.
  2. Remove the mid aero shield panel. See 패널 - 에어로 실드 - 중간(탈거 및 교체).
  3. Position an oil drain collector under the rear drive unit oil pump.
  4. Pull the red tab, and then pull the red tab again to disconnect the rear subframe harness from the rear drive unit oil pump connector.
  5. Remove the bolts (x2) that attach the rear drive unit oil pump to the rear drive unit.
  6. Use a plastic pry tool to separate the rear drive unit oil pump from the rear drive unit, remove the oil pump, and allow the fluid to drain.

장착

  1. Apply a light coat of KAF1 oil to the O-rings of the rear drive unit oil pump, and then wipe away any excess oil.
  2. Install the rear drive unit oil pump into the rear drive unit, and then install the bolts (x2) that attach the oil pump to the drive unit.
    5 Nm (3.7 lbs-ft) +20 deg
  3. Drain the gearbox fluid from the rear drive unit. See 기어박스 오일 - 후륜 구동 장치(4DU)(배출 및 보충).
  4. Refill the rear drive unit with gearbox fluid. See 기어박스 오일 - 후륜 구동 장치(4DU)(배출 및 보충).
  5. Install the mid aero shield panel. See 패널 - 에어로 실드 - 중간(탈거 및 교체).
  6. Enable Service Mode on the touchscreen. See 정비 모드.
  7. Perform a software reinstall. See 소프트웨어 재설치 - 터치스크린.
  8. Disable Service Mode. See 정비 모드.
  9. Remove the vehicle from the 2 post lift. See 차량 올리기 - 2 포스트 리프트.