2024-04-08

Octovalve (Remove and Replace)

Correction code 18400202 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Octovalve (Remove and Replace).
Description Torque Value Recommended Tools Reuse/Replace Notes
옥토밸브를 수퍼매니폴드에 고정하는 나사(4개)
5 Nm (3.7 lbs-ft)
  • Torx T25 소켓
Reuse

Remove

  1. LH 전면 도어를 열고 LH 전면 창문을 내립니다.
  2. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  3. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  4. 외기 흡기 덕트를 탈거합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  5. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. 12V 배터리를 탈거합니다. 참조 항목: 12V/LV Battery (Remove and Replace).
  7. 냉각수 보틀을 제거합니다. 참조 항목: Coolant Bottle (Remove and Replace).
  8. 커넥터 잠금 장치를 분리한 다음 옥토밸브 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  9. 옥토밸브를 슈퍼매니폴드에 고정하는 나사(4개)를 탈거하고 차량에서 옥토밸브를 탈거합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓

Install

  1. 옥토밸브를 슈퍼매니폴드에 배치한 다음 옥토밸브를 슈퍼매니폴드에 고정하는 나사(4개)를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    패스너를 장착하기 전에 옥토밸브의 다우얼이 수퍼매니폴드와 맞물려 있는지 확인합니다. 옥토밸브가 수퍼매니폴드와 수평을 이루어야 제대로 밀봉됩니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T25 소켓
  2. 옥토밸브 커넥터를 연결한 다음 커넥터 잠금 장치를 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  3. 냉각수 보틀을 장착합니다. Coolant Bottle (Remove and Replace)을(를) 참조하십시오.
  4. 12V 배터리를 장착합니다. 참조 항목: 12V/LV Battery (Remove and Replace).
  5. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. Toolbox 3가 설치된 노트북을 차량에 연결합니다.
  7. Toolbox 에서 Actions/Autodiag탭을 클릭하고 검색 필드에 "Thermal"을 입력한 후 TEST-SELF_VCFRONT_X_FIVE-WAY-VALVEvia Toolbox: (link)via Service Mode: Thermal ➜ Coolant System ➜ Coolant Valve Test을(를) 클릭하고 Run을 클릭한 다음 루틴이 완료될 때까지 기다립니다.
  8. Actions/Autodiag 탭을 클릭하고 검색 필드에 "Purge"를 입력한 후 TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    을(를) 클릭하고 Run을 클릭한 다음 루틴이 완료될 때까지 기다립니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    차량이 주행 상태가 아닌지 확인합니다. 중지 메시지에도 불구하고, 플랜이 계속 실행되고 있습니다. 냉각수 펌프 소리가 들립니다. 테스트에 약 10분이 걸립니다. Coolant pump speeds can be monitored in Service Mode + (see Service Mode Plus), in the CAN Viewer submenu. 공회전 속도 = ~1500RPM. 테스트 속도는 3500-6500RPM이고 밸브는 직렬과 병렬 간에 전환합니다. 차량을 주행 상태로 두면 이 루틴이 중지됩니다. 속도가 7000RPM에서 맴돌면 펌프가 공기 잠김 상태이므로 진공 충전을 다시 수행합니다. 냉각수 수위가 보틀의 NOM과 MAX 선 사이에 도달하도록 계속해서 냉각수를 추가하고 배출합니다. 완료되면 창 오른쪽 상단에 있는 "X"를 선택하여 닫습니다.
  9. 냉각수 수위를 검사하고 필요한 경우 보충합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각수 수위가 Max 선에 있는지 확인합니다.
  10. 냉각수 보틀 캡을 장착합니다.
  11. Actions/Autodiag 탭을 클릭하고 검색 필드에 "Thermal"을 입력한 후 TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    을(를) 클릭하고 Run을 클릭한 다음 루틴이 완료될 때까지 기다립니다.
  12. Toolbox를 연결 해제하고 차량에서 노트북을 제거합니다.
  13. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  14. 외기 흡기 덕트를 장착합니다. 참조 항목: Duct - Fresh Intake (Remove and Replace).
  15. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  16. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.