2024-11-22

Module - Cooling Fan (Remove and Replace)

Correction code 18201312 1.26 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

토크 규격

표 1. Torque Specifications: GUID-81F39FBB-029E-4729-9A82-C8F42F8879FC.html
Description Torque Value Recommended Tools Reuse/Replace Notes
후드 내 보관 유닛 보강재 브래킷을 냉각 팬에 고정하는 볼트
48 Nm (35.4 lbs-ft)
  • 외부 Torx Plus EP14
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 3인치 익스텐션
Reuse
냉각 팬 모듈의 하단 LH 및 RH를 앵클 캐처에 고정하는 볼트
10 Nm (7.4 lbs-ft)
  • 8mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 4인치 익스텐션
Reuse

Install

  1. 보조 작업자와 함께 냉각 팬 모듈 어셈블리를 차량에 배치한 다음 모듈 어셈블리를 차량에 고정하는 볼트를 느슨하게 장착합니다.
  2. 냉각 팬 모듈의 LH 및 RH를 차량에 고정하는 볼트를 규격 토크로 조입니다.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    보조 작업자가 어셈블리를 지지해주는 것이 좋습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 8mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 4인치 익스텐션
    그림 1. LH
    그림 2. RH
  3. 라디에이터 방출 호스에서 플러그를 탈거하고 암수 피팅을 연결한 다음 호스 클립을 조입니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    피팅에 대해 밀고 당기기 연결 검사를 수행하여 단단히 고정되었는지 확인합니다.
  4. 라디에이터 인입 호스에서 플러그를 탈거하고 암수 피팅을 연결한 다음 호스 클립을 조입니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    피팅에 대해 밀고 당기기 연결 검사를 수행하여 단단히 고정되었는지 확인합니다.
  5. 냉각 팬 모듈 커넥터에서 전기 하네스를 연결한 다음 커넥터 잠금 장치를 체결합니다.
  6. 전면 밸런스를 장착합니다. 참조 항목: Valance - Front Fascia (Remove and Replace).
  7. 전면 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  8. 타이어가 지면에 닿을 때까지 차량을 내립니다.
  9. 후드 내 보관 유닛 보강재 브래킷을 냉각 팬에 배치한 다음, 브래킷을 팬에 고정하는 볼트를 장착합니다.
    48 Nm (35.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 외부 Torx Plus EP14
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 3인치 익스텐션
  10. 외기 온도 센서 전기 커넥터를 연결한 다음 센서 커버를 액티브 그릴 셔터에 장착합니다.
  11. 액티브 그릴 셔터 전기 커넥터를 연결한 다음 커넥터 잠금 장치를 체결합니다.
  12. 냉각 시스템 진공 재충전을 수행합니다. 참조 항목: Cooling System (Vacuum Refill).
  13. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  14. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    Informational PurposesAn informational icon, calling your attention
    참고
    루틴이 완료되면 창 오른쪽 상단에 있는 "X"를 선택하여 닫습니다.
  15. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  16. LH 전면 도어를 닫고 LH 전면 창문을 올립니다.