2024-02-16

Door Assembly - Charge Port (EMEA) (Remove and Replace)

Correction code 44015302 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-02-01: 액추에이터 팬 및 모터, 차량 전기 절연 절차에 대한 단계를 삭제했습니다.
  • 2023-10-27: 차체 쪽 충전 포트(CP) 볼트 토크를 9Nm으로 업데이트합니다.
  • 2023-07-11: 차량 전기 절연 절차를 충전 포트 어셈블리 링크에 다시 추가하고 자세한 내용을 위해 장착 절차를 업데이트했습니다.
  • 2023-06-06: 충전 식별자 라벨 TPN을 1691926-00-A에서 1691926-00-B로 업데이트하고 관련 그림을 업데이트했습니다.
  • 1076921-01-B 절연 멀티미터, Fluke 1508
  • 1130480-00-A 테스트 프로브, 슬림 타입, Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

이 절차를 수행하려면 적합한 개인 보호 장비(PPE)가 필요합니다.

  • 고전압 절연 장갑
  • 가죽 장갑 보호구
  • 고전압 장갑 테스터
  • 보안경
  • 전기 위험 등급 안전 장화
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

HV 장갑 사용 기한이 만료되지 않았는지 확인하십시오. HV 장갑의 사용 기한은 장갑에 인쇄된 테스트 날짜로부터 최대 12개월이며, 장갑의 사용 기한이 12개월 기간 내에 있더라도 최초 사용일로부터 6개월간만 사용해야 합니다.

Remove

  1. 차량에서 충전 포트 어셈블리를 탈거합니다. 참조 항목: Charge Port (CCS) (Remove and Replace).
  2. LH 테일라이트 어셈블리를 탈거합니다. 참조 항목: Taillight - LH (Remove and Replace).
  3. 충전 포트 도어 주변에 보호 테이프를 장착합니다.
  4. 충전 포트 ECU에서 충전 포트 도어 하네스 커넥터를 연결 해제합니다.
  5. 차체에서 충전 포트 도어 하네스 그로밋을 분리합니다.
  6. 충전 포트 도어를 차량에 고정하는 클립(2개)을 분리하고 충전 포트 도어를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    클립을 분리하고 충전 포트 도어 하단을 바깥쪽으로 돌립니다. 액추에이터를 차체 주변으로 이동합니다.

Install

  1. 충전 포트 도어를 차량에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    액추에이터를 차체 주변으로 이동합니다.
  2. 충전 포트 도어 하네스를 차체에 고정하는 그로밋을 고정합니다.
  3. 충전 포트 도어 하네스 그로밋을 차체에 장착합니다.
  4. 충전 포트 도어 하네스 커넥터를 충전 포트 ECU에 연결합니다.
  5. 동일한 충전 포트(CP)를 다시 장착하는 경우: 충전 포트 어셈블리 후면의 충전 포트 버스바 HV 헤더를 IPA 천으로 닦은 다음 1분 동안 건조시킵니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트(CP)에 전기 접합부 컴파운드가 미리 도포되어 있으므로, 새 충전 포트 어셈블리를 장착할 경우 이 단계를 건너뜁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    플라스틱 트림 공구를 사용하여 IPA 천을 충전 포트 버스바 HV 헤더의 틈새에 밀어 넣습니다.
  6. 충전 포트(CP)를 차량에 배치한 다음 충전 포트(CP)를 차량에 고정하는 볼트를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하네스가 제대로 배선되었는지 확인하고, 케이블타이가 있는 접착 패드가 장착된 경우 올바르게 장착되어 있는지 확인합니다.
  7. 전기 커넥터를 충전 포트 액추에이터에 연결한 다음 잠금 탭을 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  8. 동일한 충전 포트(CP)를 다시 장착하는 경우: 충전 포트(CP) 뒤쪽 버스바 스터드의 토크 점검을 수행합니다.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트 어셈블리를 장착하는 경우 이 단계를 건너뜁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 비트
    • 4인치 익스텐션
    • 래칫/토크 렌치
  9. IPA 천을 사용하여 충전 포트 버스바 리드에서 잔류물 및 잔해를 모두 닦은 다음 1분 동안 자연 건조시킵니다.
    그림 1. 버스바 브래킷 디자인이 다를 수 있음
  10. 동일한 충전 포트(CP)를 다시 장착하는 경우: 각 충전 포트 버스바 리드(2개)에서 충전 포트(CP)와 접촉하는 면에 전기 접합부 컴파운드를 두 방울씩 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트(CP)에 전기 접합부 컴파운드가 미리 도포되어 있으므로, 새 충전 포트 어셈블리를 장착할 경우 이 단계를 건너뜁니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    접촉면이 전기 접합부 컴파운드로 완전히 덮였는지 확인합니다.
    그림 2. 버스바 브래킷 디자인이 다를 수 있음
  11. 충전 포트 버스바를 충전 포트(CP)에 배치한 다음 버스바 리드를 충전 포트(CP)에 고정하는 너트(2개)를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  12. 나중에 이 절차에서 저항을 측정하는 것에 대비하여 Hioki 저항계의 영점 조정을 수행합니다. 참조 항목: Resistance Meter (Zero Adjust).
  13. 두 개의 잠금 탭 체결 여부를 확인하면서 버스바 브래킷에 안전 캡을 장착합니다.
  14. 충전 포트(CP)에 3상 커넥터를 연결한 다음 잠금 탭을 아래로 밉니다.
    그림 3. Model 3에서 본 모습, Model Y도 유사함
  15. 해당 테일라이트를 다시 장착해야 하는 경우 각 테일라이트 마운팅 볼트(2개) 및 테일라이트 전기 커넥터(1개) 주변에서 개스킷을 교체합니다.
  16. LH 테일라이트 스터드를 그로밋에 배치한 다음, 테일라이트를 차체에 장착합니다.
  17. 테일라이트를 차량에 고정하는 너트(2개)를 장착합니다.
    3.2 Nm (2.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 8mm 12 포인트 딥소켓
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  18. 전기 하네스를 테일라이트 커넥터에 연결한 다음 커넥터 잠금 장치를 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    커넥터에 빨간색 잠금 탭이 있는 경우: Push the red locking tab into the connector to engage the connector lock.
  19. 충전 포트 어셈블리를 차량에 계속해서 장착합니다. 참조 항목: Charge Port (CCS) (Remove and Replace).
  20. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  21. HEPA 필터 어셈블리를 장착합니다. 참조 항목: Assembly - Filter - HEPA (Remove and Install).
  22. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  23. 차량 소프트웨어를 다시 설치합니다. 참조 항목: Software Reinstall - Touchscreen.
  24. 충전 시스템 작동을 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    고객의 충전 장비가 있는 경우, 해당 장비를 사용합니다.
    1. 충전 포트 도어의 하단 RH 모서리를 살짝 눌러 충전 포트(CP)를 연 다음 충전 포트 도어를 닫습니다.
    2. UMC 또는 월 커넥터를 사용하고 핸들의 버튼을 눌러 충전 포트 도어를 엽니다.
      Informational PurposesAn informational icon, calling your attention
      참고
      도어를 닫은 후 도어가 다시 열릴 때까지 잠시 제한 시간이 경과될 수 있습니다.
    3. 충전 핸들을 충전 포트(CP)에 연결하고 차량이 충전 중인지 확인하십시오.
    4. 충전 핸들을 분리하고 충전 포트 도어가 닫히는지 확인합니다.
  25. 유럽만 해당: 원래 부품에 있는 경우 그림과 같이 충전 포트 어셈블리의 페이스 플레이트에 CKL 충전 식별자 라벨(1691926-00-B)을 설치합니다.