2023-07-20

Latch Actuator - Charge Port (3 Phase) (Remove and Replace)

Correction code 44014012 0.84 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 1076921-00-B 절연 멀티미터, Fluke 1507 (북미)
  • 1076921-00-A 절연 멀티미터, Fluke 1587 (유럽 및 중동·아프리카)
  • 1076921-01-B 절연 멀티미터, Fluke 1508 (APAC)
  • 1108272-00-B 캡, 로직 연결, 인버터, 3DU
  • 1130480-00-A 테스트 프로브, 슬림, Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

이 절차를 수행하려면 적합한 PPE(개인 보호 장비)가 필요합니다.

  • 고전압(HV) 절연 장갑
  • 가죽 장갑 보호구
  • 고전압 장갑 테스터
  • 보안경
  • 전기 위험 등급 안전 장화
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

HV 장갑 사용 기한이 만료되지 않았는지 확인하십시오. HV 장갑의 사용 기한은 장갑에 인쇄된 테스트 날짜로부터 최대 12개월이며, 장갑의 사용 기한이 12개월 기간 내에 있더라도 최초 사용일로부터 6개월간만 사용해야 합니다.

  • 2023-07-11: 더 자세한 단계 및 이미지를 추가했습니다.

Remove

  1. 충전 포트를 제거합니다. Charge Port (CCS) (Remove and Replace)을(를) 참조하십시오.
  2. 잠금 핀을 안쪽으로 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    핀이 완전히 안으로 들어갔는지 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    기어 액추에이터 로커 암은 위로 올려진 상태여야 합니다.
  3. 충전 포트 어셈블리에서 수동 해제 케이블을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    로커 암 위치를 기록합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    로커 암을 바깥쪽으로 조심스럽게 들어 올립니다.
  4. 래치 액추에이터 어셈블리를 충전 포트 어셈블리에 고정하는 볼트(4개)를 탈거한 다음, 충전 포트에서 래치 액추에이터 어셈블리릍 탈거합니다.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • T20 비트
  5. 래치 액추에이터 브래킷에서 래치 액추에이터를 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    액추에이터 핀을 바깥쪽으로 밀어 래치 액추에이터에서 분리한 다음 브래킷 커버에서 분리합니다. 래치 액추에이터를 브래킷에서 들어 올려 분리합니다.

Install

  1. 래치 액추에이터 어셈블리를 설정합니다.
    1. O링을 올바른 위치에 장착합니다.
    2. 래치 액추에이터를 브래킷에 밀어 넣습니다.
    3. 액추에이터 잠금 핀 어셈블리를 조심스럽게 정렬하여 장착합니다.
  2. 래치 액추에이터 어셈블리를 충전 포트 어셈블리에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    조심스럽게 래치 액추에이터 어셈블리를 안쪽으로 밀어 잠금 핀을 정렬합니다.
  3. 래치 액추에이터 어셈블리를 충전 포트 어셈블리에 고정하는 볼트(4개)를 장착합니다.
    1.8 Nm (1.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • T20 비트
  4. 수동 해제 케이블을 래치 액추에이터에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    조심스럽게 액추에이터 로커 암이 완전히 안착할 때까지 밀어 넣은 다음, 케이블을 브래킷에 고정합니다.
  5. 충전 포트를 장착합니다. Charge Port (CCS) (Remove and Replace)을(를) 참조하십시오.