08/04/2024 19:52:27
Event Data Recorder Retrieval
경고
이 절차는 검증되었지만 초안입니다. 경고와 주의사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.
참고
Refer to CD-20-20-001 for Model Y Event Data Recorder (EDR) guide.
참고
Use the following procedure(s) for Model Y Non-Structural Pack EDR retrieval as required:
참고
Use the following procedure(s) for Model Y Structural Pack EDR retrieval as required:
Establish a Direct-to-Module Connection (Non-Structural Pack)
- Open all of the doors.
- Lower all of the windows.
- On the vehicle touchscreen, select the Tesla symbol, and then confirm and note the vehicle’s firmware version.
- Remove the Restraint Control Module (RCM). See 모듈 - 구속 장치 제어(구조용 팩 이외) (탈거 및 교체).
-
Connect the EDR extraction harness connectors (x2) to the RCM.
참고다음 공구 사용을 권장합니다.
- EDR extraction harness, RCM, Bosch MS-M3-MY - 1492139-00-B
-
Connect the EDR extraction harness connector to the PCAN USB to CAN adapter connector.
참고다음 공구 사용을 권장합니다.
- PCAN USB to CAN adapter - 1016990-00-A
- Connect the PCAN USB to CAN adapter dongle connector to the laptop USB port.
-
Connect the XP-20 (heavy duty) jump start 12V power to the EDR extraction harness.
참고Jump start, XP-20 (heavy duty) - 1016990-00-A
-
Open the Tesla EDR Retrieval Program.
참고The program will automatically try to connect to RCM and will display a green circle in the lower left corner when connected.
- Once the Tesla EDR Retrieval Program connection is established, click "Run EDR Retrieval", and then follow the on-screen prompts to retrieve and save the EDR data.
-
Use the retrieved data to "Generate a Report". See https://edr.tesla.com.
참고EDR retrieval time will vary based on the user and retrieved data.
-
Close the Tesla EDR Retrieval Program.
참고Select "X" at the top right of the window to close the program once EDR retrieval is complete.
- Disconnect the XP-20 (heavy duty) jump start 12V power from the EDR extraction harness.
- Disconnect the PCAN USB to CAN adapter dongle connector from the laptop USB port.
- Disconnect the EDR extraction harness connector from the PCAN USB to CAN adapter connector.
- Disconnect the EDR extraction harness connectors (x2) from the RCM.
- Install the RCM. See 모듈 - 구속 장치 제어(구조용 팩 이외) (탈거 및 교체).
- Raise all of the windows.
- Close all of the doors.
Establish a Direct-to-Module Connection (Structural Pack)
- Remove the RCM. See 모듈 - 구속 제어(구조용 팩)(탈거 및 교체).
-
Connect the EDR extraction harness connectors (x2) to the RCM.
참고다음 공구 사용을 권장합니다.
- EDR extraction harness, RCM, Bosch MS-M3-MY - 1492139-00-B
-
Connect the EDR extraction harness connector to the PCAN USB to CAN adapter connector.
참고다음 공구 사용을 권장합니다.
- PCAN USB to CAN adapter - 1016990-00-A
- Connect the PCAN USB to CAN adapter dongle connector to the laptop USB port.
-
Connect the XP-20 (heavy duty) jump start 12V power to the EDR extraction harness.
참고Jump start, XP-20 (heavy duty) - 1016990-00-A
-
Open the Tesla EDR Retrieval Program.
참고The program will automatically try to connect to RCM and will display a green circle in the lower left corner when connected.
- Once the Tesla EDR Retrieval Program connection is established, click "Run EDR Retrieval", and then follow the on-screen prompts to retrieve and save the EDR data.
-
Use the retrieved data to "Generate a Report". See https://edr.tesla.com.
참고EDR retrieval time will vary based on the user and retrieved data.
-
Close the Tesla EDR Retrieval Program.
참고Select "X" at the top right of the window to close the program once EDR retrieval is complete.
- Disconnect the XP-20 (heavy duty) jump start 12V power from the EDR extraction harness.
- Disconnect the PCAN USB to CAN adapter dongle connector from the laptop USB port.
- Disconnect the EDR extraction harness connector from the PCAN USB to CAN adapter connector.
- Disconnect the EDR extraction harness connectors (x2) from the RCM.
- Install the RCM. See 모듈 - 구속 제어(구조용 팩)(탈거 및 교체).