2024-09-09

Assembly - Filter - HEPA (Remove and Install)

Correction code 18105401 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-09-12: HEPA 필터 어셈블리를 차량에 고정하는 볼트(2개)의 토크 정보를 수정했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.
표 1. Torque Specifications: Assembly - Filter - HEPA (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
후드 내 보관 유닛을 워셔액 저장 탱크 주입구에 고정하는 볼트
5 Nm (3.7 lbs-ft)
  • 10mm 소켓
  • 래칫/토크 렌치
  • 코드리스 래칫/임팩트 드라이버
  • 4인치 익스텐션
Reuse
HEPA 필터 어셈블리를 차량에 고정하는 볼트(2개)
10 Nm (7.4 lbs-ft)
  • 4인치 익스텐션
  • 10mm 소켓
  • 코드리스 래칫/임팩트 드라이버
  • 래칫/토크 렌치
Reuse

Remove

  1. LH 전면 도어를 열고 LH 전면 창문을 완전히 내립니다.
  2. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  3. 후드 내 보관 유닛을 워셔액 저장 탱크 넥에 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    일부 차량에는 이 위치에 푸시 클립이 제공되었을 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 래칫/토크 렌치
    • 코드리스 래칫/임팩트 드라이버
    • 4인치 익스텐션
  4. 워셔액 저장 탱크에서 워셔액 저장 탱크 넥을 분리한 다음 넥을 한쪽으로 치워둡니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    넥에서 호스를 탈거할 필요가 없습니다.
  5. HEPA 필터 어셈블리를 차량에 고정하는 볼트(2개)를 탈거한 다음 차량에서 어셈블리를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    어셈블리의 후면 가장자리를 위쪽으로 회전하여 브레이크 오일 저장 탱크를 치운 다음 어셈블리를 위쪽으로 들어 올려 후드 내 보관 유닛을 치웁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 4인치 익스텐션
    • 10mm 소켓
    • 코드리스 래칫/임팩트 드라이버
    • 래칫/토크 렌치

Install

  1. 장착을 위해 HEPA 필터 어셈블리를 배치하려면 필터 어셈블리의 앞쪽 가장자리를 후드 내 보관 유닛 아래에 배치한 다음, 필터 어셈블리의 후면 가장자리를 브레이크액 저장 탱크를 지나도록 조심스럽게 이동합니다.
  2. HEPA 필터 어셈블리를 차량에 고정하는 볼트(2개)를 장착한 다음, 차량에서 어셈블리를 탈거합니다.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    프렁크 어셈블리를 지나 전면 가장자리를 아래로 회전시킨 다음, 후면 가장자리를 브레이크 저장 탱크를 지나 제자리로 조심스럽게 이동합니다. 필터의 RH를 부드럽게 눌러 씰을 덕트에 안착시킵니다. 재작업에는 새 볼트가 필요합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 4인치 익스텐션
    • 10mm 소켓
    • 코드리스 래칫/임팩트 드라이버
    • 래칫/토크 렌치
  3. 워셔 탱크 넥을 워셔 탱크에 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    워셔 호스가 올바르게 배치되었는지 확인합니다.
  4. 후드 내 보관 유닛을 워셔액 저장 탱크 넥에 고정하는 볼트를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    일부 차량에는 이 위치에 푸시 클립이 제공되었을 수 있습니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 래칫/토크 렌치
    • 코드리스 래칫/임팩트 드라이버
    • 4인치 익스텐션
  5. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  6. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.