2025-02-28

Mirror - Door - LH (Remove and Replace)

Correction code 12091102 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2025-02-10: 새로운 유형의 도어 미러용 펌웨어 업데이트에 대한 정보를 추가했습니다.
  • 2023-07-20: 미러 조정 모터의 내부 쇼트로 인해 미러를 교체하는 경우의 차체 컨트롤러 초기화에 대한 정보를 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Torque Specifications

표 1. Torque Specifications: Mirror - Door - LH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 도어 미러를 도어에 고정하는 볼트
15 Nm (11.1 lbs-ft)
  • 10mm 소켓
  • 4인치 익스텐션
Reuse
Informational PurposesAn informational icon, calling your attention
참고
최신 버전의 외장 도어 미러의 경우 미러 액추에이터의 빠른 마모 진행 방지를 위해 펌웨어 버전이 2025.2.3 이상이어야 합니다.

Remove

  1. 펌웨어 버전을 확인하십시오. 펌웨어 버전이 2025.2.3보다 이전인 경우 펌웨어를 2025.2.3 이상 버전으로 업데이트하십시오. 참조 항목: Software Update.
    Informational PurposesAn informational icon, calling your attention
    참고
    서비스 방문에 교정 코드 00020003를 별도 활동으로 추가합니다.
  2. LH 도어 미러 스컬캡을 탈거합니다. 참조 항목: Skull Cap - Door Mirror - LH (Remove and Replace).
  3. 전면 LH 도어 트위터를 탈거합니다. 참조 항목: Tweeter - Front Door - LH (Remove and Replace).
  4. LH 전면 도어 트림 패널 후면에서 리플렉터를 탈거합니다.
  5. 리플렉터를 LH 전면 도어 트림 패널의 후면 가장자리에 고정하는 클립을 분리한 다음 트림 패널에서 리플렉터를 탈거합니다.
  6. 도어에 트림 패널을 고정하는 나사를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T30 소켓
    • 4인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
    그림 1. 후면
    그림 2. 중간
    그림 3. 전면
  7. LH 전면 도어 트림 패널을 바깥쪽으로 당겨 패널을 도어에 고정하는 클립(9개) 및 위치 지정 핀(2개)을 분리한 다음 도어 패널을 조심스럽게 시계 방향으로 90도 돌리고 손상을 방지하기 위해 부드러운 표면에 놓습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    이때 도어에서 트림 패널을 탈거하지는 않습니다.
    그림 4. 트림 패널 클립 위치
    그림 5. 도어 클립 위치
  8. LH 도어 미러 전기 커넥터를 연결 해제합니다.
  9. 창문 전기 하네스를 도어에 고정하는 클립을 풉니다.
  10. LH 도어 글라스 런 씰을 도어에 고정하는 클립을 분리한 다음 도어에서 씰을 제거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    글라스 런 클립 손상을 방지하려면 트림 탈거 공구를 사용하여 클립을 한 번에 하나씩 부드럽게 들어 올립니다.
  11. 볼트 캡을 탈거한 다음 LH 도어 미러를 도어에 고정하는 볼트(3개)를 탈거합니다.
    15 Nm (11.1 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고

    Use only hand tools to remove or install the fasteners. Do not use impact or power tools.

    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 4인치 익스텐션
  12. LH 도어 미러 어셈블리를 위로 들어 올려 도어에서 분리합니다.
  13. 도어를 통해 하네스 그로밋을 누른 다음 도어를 통해 전기 하네스를 배치하여 LH 도어 미러 어셈블리를 탈거합니다.

Install

Informational PurposesAn informational icon, calling your attention
참고
미러 어셈블리가 조정 모터의 내부 쇼트로 인해 교체되었다면, 영향을 받은 차체 컨트롤러를 초기화(정비 모드 > 저전압 > 전력 배포 > VCLeft 초기화 또는 VCRight 초기화)해야 합니다. 이렇게 하면 회로 보호가 해제되고 새 미러가 완전히 작동할 수 있습니다.

Installation procedure is the reverse of removal.