Bracket - Ancillary Connector Dash Mount (Remove and Replace)
Correction code
18200012
0.48
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See Flat Rate
Times to learn more about FRTs and how they are created. To provide feedback on
FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 개인 보호 to make sure wearing proper PPE when
performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.
Remove
- 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
- 2열 하단 시트 쿠션을 탈거합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
- 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
- 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
- Perform Vehicle HV Disablement Procedure. See Vehicle HV Disablement Procedure.
- 전면 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
-
커넥터 잠금 장치를 분리한 다음 HV 배터리의 AC 컴프레서 HV 하네스 커넥터를 연결 해제합니다.
참고커넥터에서 빨간색 잠금 탭을 당겨 분리합니다.
-
방화벽 LH 쪽의 스터드에서 HV 커넥터 마운트 브래킷을 분리합니다.
-
마운트 브래킷에서 HV 커넥터를 고정하는 클립을 분리한 다음 차량에서 브래킷을 탈거합니다.
Install
-
HV 커넥터를 마운트 브래킷에 장착합니다.
-
HV 커넥터 마운트 브래킷 스터드를 방화벽 LH 쪽에 장착합니다.
-
양쪽 AC 컴프레서 HV 하네스 커넥터를 HV 배터리에 연결한 다음 커넥터 잠금 장치를 체결합니다.
참고커넥터가 안착되고 딸깍하는 소리가 난 후 두 번째 잠금 장치를 커넥터를 향해 돌려 체결합니다.
- 전면 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
- 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
- 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
- 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
- 리프트에서 차량을 내립니다. 참조 항목: Raise Vehicle - 2 Post Lift.