2024-06-11

Module - Restraint Control (Non-Structural Pack) (Remove and Replace)

Correction code 20015002 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-05-14: Toolbox 3 루틴을 터치스크린을 사용한 루틴으로 교체하였습니다.
  • 2024-04-18: 중복되는 ODIN 루틴을 삭제하고 헤드라이트 조준 지침을 개선했습니다.
  • 2023-08-24: LV가 연결 해제되었는지 확인하는 경고를 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Disconnect the 12V/LV battery and the First Responder Loop. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see 에어백 및 안전보조장치(SRS) 사전 주의 사항.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Supplementary Restraint System (SRS) components can be hazardous if not handled properly. For more information on SRS precautions, see 에어백 및 안전보조장치(SRS) 사전 주의 사항.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
While performing any Supplementary Restraint System (SRS) related repairs, it is important to disconnect 12V/LV power, by disconnecting the 12V/LV battery and the First Responder Loop. If the vehicle’s 12V/LV power is NOT disconnected and the Restraint Control Module is removed or disturbed, this can result in the deployment of the vehicle’s airbags.

Torque Specifications

표 1. 토크 규격: Module - Restraint Control (Non-Structural Pack) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
구속 장치 제어 모듈에서 차체 연결 너트
8 Nm (5.9 lbs-ft)
  • 10mm 소켓
  • 2인치 익스텐션
  • ¼인치 표준 래칫
  • ¼인치 토크 렌치(장착 전용)
Replace

Remove

  1. 센터 콘솔을 탈거합니다. 참조 항목: Center Console (Remove and Install).
  2. 센터 콘솔 지지 브래킷을 차량에 고정하는 하네스 클립(1개)과 탭(4개)을 분리한 다음 브래킷을 앞쪽으로 조심스럽게 밀어 차량에서 탈거합니다.
  3. 12V/LV 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Make sure LV is disconnected before continuing to the next step.
  4. 잠금 레버을(를) 분리한 다음 구속장치 제어 모듈에서 전기 하네스를 연결 해제합니다.
  5. 구속장치 제어 모듈을 차체에 고정하는 너트(3개)를 탈거하여 폐기한 다음 차량에서 모듈을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)

장착

  1. 구속장치 제어 모듈을 차량에 배치한 다음 구속장치 제어 모듈을 차량에 고정하는 새 너트(3개)를 장착합니다.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 2인치 익스텐션
    • ¼인치 표준 래칫
    • ¼인치 토크 렌치(장착 전용)
  2. 전기 하네스 커넥터(2개)를 구속장치 제어 모듈에 연결한 다음 잠금 레버를 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    계속 진행하기 전에 두 커넥터 모두에 밀고 당기기 검사를 수행합니다.
  3. 센터 콘솔 지지 브래킷을 차량에 배치하고, 브래킷을 뒤쪽으로 밀은 다음 브래킷을 차량에 고정하는 하네스 클립(1개)과 탭(4개)을 장착합니다.
  4. 센터 콘솔을 장착합니다. 참조 항목: Center Console (Remove and Install).
  5. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. 터치스크린을 통해 차량 소프트웨어를 재설치합니다. 참조 항목: Software Reinstall - Touchscreen.
  7. 정비 모드 플러스를 시작합니다. 참조 항목: Service Mode Plus
  8. 터치스크린에서 Service Mode > Safety and Restraints > Airbags > RCM > Post Replacement Tasks를 터치합니다.
  9. 다음 화면에서 Run을 터치한 다음 루틴이 완료될 때까지 기다립니다.
  10. 터치스크린에서 헤드라이트 수평 조정 시스템을 확인합니다.
    • 헤드라이트 수평 조정 시스템이 "지상고 센서"인 경우 정비 모드를 종료하고 Service Mode을(를) 참조하며 이 절차는 중단합니다.
    • 헤드라이트 수평 조정 시스템이 "가상 피치 센서"인 경우 정비 모드를 종료하고 Service Mode을(를) 참조하여 다음 단계를 계속합니다.
  11. 헤드라이트를 조정합니다.