2024-06-11

Module - Restraint Control (Structural Pack) (Remove and Replace)

Correction code 20015022 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-05-14: Toolbox 3 루틴을 터치스크린을 사용한 루틴으로 교체하였습니다.
  • 2024-04-18: 중복되는 ODIN 루틴을 삭제하고 헤드라이트 조정 지침을 개선했습니다.
  • 2023-08-24: LV가 연결 해제되었는지 확인하는 경고를 추가했습니다.
  • 2023-04-25: 구속 제어 모듈 버전 12.1을 위한 TBX 루틴을 업데이트했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Make sure 12V/LV power has been disconnected for at least 1 minute before disconnecting the electrical harness from Supplementary Restraint System (SRS) components, such as Restraint Control Module, sensors, airbags, etc. Disconnect the 12V/LV battery and the First Responder Loop. Failure to do so can result in unintended safety system behaviors. For more information on SRS precautions, see 에어백 및 안전보조장치(SRS) 사전 주의 사항.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Supplementary Restraint System (SRS) components can be hazardous if not handled properly. For more information on SRS precautions, see 에어백 및 안전보조장치(SRS) 사전 주의 사항.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
While performing any Supplementary Restraint System (SRS) related repairs, it is important to disconnect 12V/LV power, by disconnecting the 12V/LV battery and the First Responder Loop. If the vehicle’s 12V/LV power is NOT disconnected and the Restraint Control Module is removed or disturbed, this can result in the deployment of the vehicle’s airbags.

Remove

  1. 전면 도어를 열고 전면 창문을 내립니다.
  2. 전면 동승석 시트를 뒤로 이동합니다.
  3. RH 센터 콘솔 사이드 패널을 탈거합니다. 참조 항목: Side Panel - Center Console - LH (Remove and Replace).
  4. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  5. HEPA 필터 어셈블리를 차량에 고정하는 볼트(2개)를 탈거한 다음 차량에서 어셈블리를 탈거합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    어셈블리의 후면 가장자리를 위쪽으로 회전하여 브레이크 오일 저장 탱크를 치운 다음 어셈블리를 위쪽으로 들어 올려 후드 내 보관 유닛을 치웁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
  6. LV 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Make sure LV is disconnected before continuing to the next step.
  7. 구속 제어 모듈 커넥터(2개)를 연결 해제합니다.
  8. 구속 제어 모듈을 차량에 고정하는 너트(3개)를 탈거하여 폐기합니다.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
  9. 구속 제어 모듈을 정렬 스터드에서 들어 올린 다음, 모듈을 라이저 아래에서 밀어 차량에서 탈거합니다.

Install

  1. 구석 제어 모듈을 라이저 아래에 배치한 다음 모듈을 정렬 스터드에 정렬합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    모듈을 라이저 아래로 밀어 넣고 구멍을 스터드에 정렬합니다
  2. 구속 제어 모듈을 차량에 고정하는 새 너트(3개)을 장착합니다.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
  3. 구속 제어 모듈 커넥터(2개)를 연결합니다.
  4. RH 센터 콘솔 사이드 패널을 장착합니다. 참조 항목: Side Panel - Center Console - LH (Remove and Replace).
  5. LV 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. HEPA 필터 어셈블리를 차량에 배치한 다음 어셈블리를 차량에 고정하는 볼트(2개)를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    프렁크 어셈블리를 지나 전면 가장자리를 아래로 회전시킨 다음 후면 가장자리를 브레이크 오일 저장 탱크를 지나 제자리로 조심스럽게 이동합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구 사용을 권장합니다.
    • 10mm 소켓
  7. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  8. 차량 펌웨어를 다시 설치합니다. 참조 항목: Software Reinstall - Touchscreen.
  9. 정비 모드 플러스를 시작합니다. 참조 항목: Service Mode Plus
  10. 터치스크린에서 Service Mode > Safety and Restraints > Airbags > RCM > Post Replacement Tasks를 터치합니다.
  11. 다음 화면에서 Run을 터치한 다음 루틴이 완료될 때까지 기다립니다.
  12. 터치스크린에서 헤드라이트 수평 조정 시스템을 확인합니다.
    • 헤드라이트 수평 조정 시스템이 "지상고 센서"인 경우 정비 모드를 종료하고 Service Mode을(를) 참조하며 이 절차는 중단합니다.
    • 헤드라이트 수평 조정 시스템이 "가상 피치 센서"인 경우 정비 모드를 종료하고 Service Mode을(를) 참조하여 다음 단계를 계속합니다.
  13. 헤드라이트를 조정합니다.