2024-04-08

Hose - Front Drive Unit Powertrain Bypass (RWD) (Remove and Replace)

Correction code 18302302 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. LH 전면 도어를 열고 창문을 완전히 내립니다.
  2. 차량을 들어 올려서 지지합니다. 참조 항목: Raise Vehicle - 2 Post Lift.
  3. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  4. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  5. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  6. 전면 에어로 실드 패널을 탈거합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  7. 냉각수 배출 용기를 차량의 RH 전면 아래에 배치합니다.
  8. 클립을 탈거하고 슈퍼매니폴드에서 파워트레인 바이패스 호스를 연결 해제한 다음 즉시 암수 피팅에 플러그를 장착합니다.
  9. 서브프레임의 RH에 파워트레인 바이패스 호스를 고정하는 클립을 풉니다.
  10. RH 휠 라이너의 하단부를 고정하는 패스너를 탈거한 다음 S자형 후크를 사용하여 라이너를 뒤쪽으로 당깁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  11. 냉각수 배출 용기를 HV 배터리의 RH 전면 아래에 배치합니다.
  12. 스프링 클립을 분리하고, HV 배터리의 RH 쪽에서 파워트레인 바이패스 호스를 연결 해제한 다음 즉시 암수 피팅에 플러그를 장착합니다.
  13. 차량에서 파워트레인 바이패스 호스를 탈거합니다.

Install

  1. 차량에 파워트레인 바이패스 호스를 장착합니다.
  2. 냉각수 플러그를 탈거하고, HV 배터리의 RH 쪽에 파워트레인 바이패스 호스를 연결한 다음 스프링 클립을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the hose is fully seated.
  3. 서브프레임의 RH에 파워트레인 바이패스 호스를 고정하는 클립을 장착합니다.
  4. 냉각수 배출 용기를 차량의 RH 전면 아래에 배치합니다.
  5. 냉각수 플러그를 탈거하고, 슈퍼매니폴드에 파워트레인 바이패스 호스를 연결한 다음 스프링 클립을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the hose is fully seated.
  6. 차량 아래에서 냉각수 배출 용기를 제거합니다.
  7. 전면 RH 휠 라이너에서 S자형 후크를 탈거하고, RH 휠 라이너의 하단부를 배치한 다음 패스너를 장착합니다.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
  8. 전면 에어로 실드 패널을 장착합니다. 참조 항목: Panel - Aero Shield - Front (Non-Structural Pack) (Remove and Replace).
  9. 타이어가 지면에 닿을 때까지 차량을 내립니다.
  10. 냉각수 보틀 캡을 탈거한 다음 냉각수 보틀을 “Max” 선까지 채웁니다.
  11. 12V 전원을 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  12. Toolbox 3.0이 설치된 노트북으로 차량에 연결합니다.
  13. Toolbox에서 Actions/Autodiag 탭을 클릭한 다음 "Purge"를 검색합니다.
  14. TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    을(를) 클릭한 다음 Run을 클릭하고 루틴이 완료될 때까지 기다립니다.
  15. 냉각수 수위를 검사하고 필요에 따라 보충한 다음 냉각수 보틀 캡을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    냉각수 수위가 “Max” 선에 있는지 확인합니다.
  16. 차량에서 노트북을 연결 해제합니다.
  17. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  18. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.