31/10/2023 20:10:53

ECU - 충전 포트(CP)(7인승)(탈거 및 교체)

교정 코드 44015032 0.36 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 검증되었지만 초안입니다. 경고와 주의사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다. 수정 사항 및 기타 의견이 있으면 ServiceDevelopment@teslamotors.com으로 알려 주십시오.
  1. Place vehicle in service mode through UI
    Informational PurposesAn informational icon, calling your attention
    참고
    Select vehicle's badge icon in Controls > Software for four seconds and then type "service" into dialog boxAnd then touch "ok"At last Select ‘X’ at top left of window to close once complete
  2. Open the LH front door.
  3. Lower all four windows
  4. Move LH front seat forward
  5. Open LH rear door
  6. Tilt 7s 2nd row 60 seat forward
    Informational PurposesAn informational icon, calling your attention
    참고
    Hold 2nd row 60 seat LH shoulder switch, Slide seat all the way forward and tit up
  7. Partially remove LH rear door seal
  8. Remove LH 7s lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    8x clips, Rear edge secures onto trunk side trim, Release front clips then rear clips
  9. Open liftgate
  10. Release 3rd row LH seat backrest
    Informational PurposesAn informational icon, calling your attention
    참고
    Front switch at LH trunk trim panel
  11. Release 3rd row RH seat backrest
    Informational PurposesAn informational icon, calling your attention
    참고
    Rear switch at LH trunk trim panel
  12. Remove rear load floor
  13. Remove trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips
  14. Remove 7s LH load floor bracket
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips
  15. Remove LH trunk side trim
    Informational PurposesAn informational icon, calling your attention
    참고
    2x connectors, 1x push clip, 8x clips, 7x tabs, guide front clip stanchions around LH C-pillar, trim part may slightly differ, by vehicle build location
  16. Release top edge of LH 7s trunk side trim and disconnect 12V outlet and trunk switch connectors
    Informational PurposesAn informational icon, calling your attention
    참고
    6x clips, 2x connectors
  17. Release remaining clips and remove LH 7s trunk side trim
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip, 5x clips, Guide front clip stanchions around LH C-pillar, Pull the top of the trunk side trim all the way down flat so it clears the edge of the folded down LH 3rd row seatback and pull straight out
  18. Disconnector ECU connectors.
    Informational PurposesAn informational icon, calling your attention
    참고
    3x connectors
  19. Remove Charge Port ECU
    Informational PurposesAn informational icon, calling your attention
    참고
    1x 10mm bolt, slide the Charge Port ECU to the front of the vehicle.
  20. Install Charge Port ECU
    Informational PurposesAn informational icon, calling your attention
    참고
    1x 10mm bolt, 3x connectors, slide the Charge Port ECU to the rear of the vehicle
  21. Re-install software via UI
    Informational PurposesAn informational icon, calling your attention
    참고
    Via Controls > Service Mode > Software Reinstall
  22. Select "REQUEST" to initiate software installation
    Informational PurposesAn informational icon, calling your attention
    참고
    Vehicle will send a request to Tesla server for the re-installation of the current firmware, Read instructions on the UI then select request if you meet the criteria, Vehicles with software version before 2022.20.7 will require internet connectivity to request the software job from the server
  23. Position LH 7s trunk side trim and install lower clips
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clips, 5x clips, Start by tucking the lower portion of the trunk side trim around the edge of the 3rd row LH backrest so it slides in and seats properly, Guide front clip stanchions around LH C-pillar
  24. Connect 12V outlet and trunk switch connectors then install top edge of LH 7s trunk side trim
    Informational PurposesAn informational icon, calling your attention
    참고
    6x clips, 2x connectors
  25. Install LH trunk pocket bracket
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip, 5x alignment tabs
  26. Install 7s LH load floor bracket
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips
  27. Install trunk sill trim
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, Seat seal around edge of trim
  28. Install rear load floor
  29. Raise 3rd row RH seat backrest to its original position
    Informational PurposesAn informational icon, calling your attention
    참고
    Manually raise backrest up to its original position until it locks into place
  30. Raise 3rd row LH seat backrest to its original position
    Informational PurposesAn informational icon, calling your attention
    참고
    Manually raise backrest up to its original position until it locks into place
  31. Close liftgate
  32. Install LH 7s lower C-pillar trim
    Informational PurposesAn informational icon, calling your attention
    참고
    8x clips, Rear edge is secures onto trunk side trim, Secure rear clips then front clips
  33. Reseat LH rear door seal
    Informational PurposesAn informational icon, calling your attention
    참고
    Seat pillar and sill trim tabs underneath seal
  34. Position 7s 2nd row 60 seat back to its original position
    Informational PurposesAn informational icon, calling your attention
    참고
    Tilt 2nd row 60 seat down, Press LH shoulder switch and slide back into original position
  35. Close LH rear door
  36. Move LH front seat to original position
  37. Verify operation of charging system
    Informational PurposesAn informational icon, calling your attention
    참고
    Use customer's charging equipment if available, Ensure all charging adapters are present
  38. Raise all four windows
  39. Close the LH front door.