2021-07-23

Air Extractor - LH (Remove and Replace)

Correction code 18105302 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. 모든 도어 및 리프트게이트를 엽니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    후면 도어에 래치를 걸어 차량의 전원이 꺼질 때 우발적으로 닫히는 것을 방지합니다.
  2. 2열 하단 시트 쿠션을 탈거합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  3. LH 하단 C필러 트림을 탈거합니다. Trim - C-Pillar - Lower - LH (Remove and Replace)을(를) 참조하십시오.
  4. 리어 트렁크 적재함 바닥을 탈거합니다. Trunk Load Floor - Rear (Remove and Replace)을(를) 참조하십시오.
  5. 전면 트렁크 적재함 바닥을 탈거합니다. Trunk Load Floor - Front (Remove and Replace)을(를) 참조하십시오.
  6. LH 적재함 바닥 브래킷을 탈거합니다. Bracket - Trunk Load Floor - LH (Remove and Replace)을(를) 참조하십시오.
  7. LH 트렁크 사이드 트림을 탈거합니다. Trim - Side - Trunk - LH (Remove and Replace)을(를) 참조하십시오.
  8. LH 공기 배출 장치를 차량에 고정하는 클립을 분리합니다.
  9. LH 공기 배출 방치를 차체 패널에 밀어 넣은 다음 바깥쪽으로 회전하여 차량에서 탈거합니다.

Install

  1. LH 공기 배출 장치를 차체 패널에 삽입하고 배출 장치를 제자리로 회전한 다음 배출 장치를 바깥쪽으로 당겨 클립을 조입니다.
  2. LH 트렁크 사이드 트림을 장착합니다. Trim - Side - Trunk - LH (Remove and Replace)을(를) 참조하십시오.
  3. LH 적재함 바닥 브래킷을 장착합니다. Bracket - Trunk Load Floor - LH (Remove and Replace)을(를) 참조하십시오.
  4. 전면 트렁크 적재함 바닥을 장착합니다. Trunk Load Floor - Front (Remove and Replace)을(를) 참조하십시오.
  5. 후면 트렁크 적재함 바닥을 장착합니다. Trunk Load Floor - Rear (Remove and Replace)을(를) 참조하십시오.
  6. LH 하단 C필러 트림을 장착합니다. Trim - C-Pillar - Lower - LH (Remove and Replace)을(를) 참조하십시오.
  7. 2열 하단 시트 쿠션을 장착합니다. Seat Cushion - Lower - 2nd Row (Remove and Replace)을(를) 참조하십시오.
  8. 모든 도어 및 리프트게이트를 닫습니다.