2021-05-18

Riser - Instrument Panel (Remove and Replace)

Correction code 14050082 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Remove

  1. LH 전면 도어를 열고 LH 전면 창문을 완전히 내립니다.
  2. 운전석 시트를 완전히 뒤로 이동합니다.
  3. LH 전면 플로어 매트를 탈거합니다.
  4. LH 센터콘솔 사이드 패널 카펫을 탈거합니다. Side Panel - Center Console - LH (Remove and Replace)을(를) 참조하십시오.
  5. 카펫을 계기판 높이 조절 장치에 고정하는 클립을 탈거합니다.
  6. 계기판 높이 조절 장치를 크로스 카 빔에 고정하는 볼트를 탈거합니다.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용할 것을 권장합니다.
    • 13 mm 소켓
    • 플렉스 헤드 래칫 / 플렉스 헤드 토크 렌치
    • 3인치 익스텐션
  7. 계기판 높이 조절 장치를 차체에 고정하는 너트를 탈거한 다음 차량에서 높이 조절 장치를 탈거합니다.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    탈거 도중 계기판 높이 조절 장치의 방향에 유의하십시오.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 도구 사용을 권장합니다.
    • 13 mm 소켓
    • 플렉스 헤드 래칫 / 플렉스 헤드 토크 렌치
    • 6인치 익스텐션

Install

  1. 계기판 높이 조절 장치를 차량에 배치한 다음 너트를 장착합니다.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    장착 도중 계기판 높이 조절 장치의 방향에 유의하십시오.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 도구 사용을 권장합니다.
    • 13 mm 소켓
    • 플렉스 헤드 래칫 / 플렉스 헤드 토크 렌치
    • 6인치 익스텐션
  2. 계기판 높이 조절 장치를 크로스 카 빔에 고정하는 볼트를 장착합니다.
    25 Nm (18.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용할 것을 권장합니다.
    • 13 mm 소켓
    • 플렉스 헤드 래칫 / 플렉스 헤드 토크 렌치
    • 3인치 익스텐션
  3. 카펫을 계기판 높이 조절 장치에 고정하는 클립을 장착합니다.
  4. LH 센터콘솔 사이드 패널 카펫을 장착합니다. Side Panel - Center Console - LH (Remove and Replace)을(를) 참조하십시오.
  5. LH 전면 플로어 매트를 장착합니다.
  6. 운전석 시트를 원래 위치로 이동합니다.
  7. LH 전면 창문을 올리고 LH 전면 도어를 닫습니다.