교정 코드 33035122 5.10 참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오.

1. Remove the HV battery from the vehicle. See HV 배터리(RWD)(탈거 및 장착).
2. Position the oil drain under front brake line junction area

   

3. Release LH front bottom sill pipe from coupling
   참고

   1x nut, 12mm, 16 Nm, 1x coupling, 13mm, 16 Nm

   

4. Release LH front top sill pipe from coupling
   참고

   1x nut, 12mm, 16 Nm, 1x coupling, 13mm, 16 Nm

   

5. Release sill pipes from LH front body clip
   참고

   1x clip

   

6. Place the oil drain pan under the brake line junction box
   참고

   Lower vehicle if necessary

   

7. Remove the LH rear brake line tube nut from rear brake pipe junction block
   참고

   1x nut, 12mm, 16 Nm

   

8. Remove the RH rear brake line tube nut from rear brake pipe junction block
   참고

   1x nut, 12mm, 16 Nm, Inner nut

   

9. Remove black clip from LH rear junction block
   참고

   1x clip

   

10. Release the brake lines from the LH rear junction block
    참고

    2x brake lines

    

11. Remove the oil drain from underneath vehicle

    

12. Raise vehicle fully and lower lift onto locks
    참고

    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
13. Remove side sill brake pipes from vehicle
    참고

    5x clips, 2x brake lines

    

    

14. Install side sill brake pipes to body
    참고

    5x clips, 2x brake lines

    

    

15. Lower vehicle partially and set onto locks
    참고

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
16. Place the oil drain pan under the brake line junction box
    참고

    Lower vehicle if necessary

    

17. Position brake lines into LH rear brake junction block
    참고

    2x brake lines

    

18. Install black clip securing brakes lines at LH rear junction block
    참고

    1x clip

    

19. Install the RH rear brake line tube nut to LH brake pipe junction block
    참고

    1x nut, 12mm, 16 Nm

    

20. Install the LH rear brake line tube nut to rear brake pipe junction block
    참고

    1x nut, 12mm, 16 Nm

    

21. Position the oil drain under front brake line junction area

    

22. Secure sill pipes to LH front body clip
    참고

    1x clip

    

23. Install LH front top sill pipe to coupling
    참고

    1x nut, 12mm, 16 Nm, 1x coupling, 13mm, 16 Nm

    

24. Install LH front bottom sill pipe to coupling
    참고

    1x nut, 12mm, 16 Nm, 1x coupling, 13mm, 16 Nm

    

25. Remove the oil drain container from underneath drive unit

    

26. Remove ancillary bay perimeter seal from HV battery pack
    참고

    Discard after removal

    

27. Install ancillary bay perimeter seal to HV battery pack
    참고

    Install new perimeter seal every time the HV battery is removed and reinstalled

    

28. Install HV battery alignment rods
    참고

    2x rods, Located on body at front of vehicle, 2x rods, Located at rear of HV battery near ancillary bay

    

    

29. Position HV battery under vehicle
    참고

    Recommend assistance

    

30. Lower vehicle onto HV battery and align holes
    참고

    Recommend assistance, Use alignment rods, Be sure coolant hoses do not get caught on alignment rods, Caution not to damage HV cable, Do not fully lower vehicle onto battery (this will help with installing battery bolts)

    

    

    

    

31. Loosely install RH bolts securing HV battery to vehicle hand tight
    참고

    8x bolts, 13mm, 35 Nm

    

32. Loosely install LH bolts securing HV battery to vehicle hand tight
    참고

    8x bolts, 13mm, 35 Nm

    

33. Remove HV battery front alignment rods
    참고

    2x rods

    

34. Install bolts securing RH front support bracket to vehicle hand tight
    참고

    4x bolts, 16mm, 110 Nm, Torque at later step

    

35. Install bolts securing LH front support bracket to vehicle hand tight
    참고

    4x bolts, 16mm, 110 Nm, Torque at later step

    

36. Install central bolts securing HV battery through center ski cover hand tight
    참고

    4x bolts, EP14, 34 Nm, Torque at later step

    

37. Open LH rear door
    참고

    Use caution while working around this area not to damage any components
38. Remove HV battery alignment rod from LH rear inner bolt location
    참고

    1x rod

    

39. Install LH rear inner HV battery bolt hand tight
    참고

    1x bolt, 16mm, 66 Nm, Lift up LH rear main carpet for access, Torque at later step

    

40. Install LH middle inner HV battery bolt hand tight
    참고

    1x bolt, 16mm, 66 Nm, Torque at later step

    

41. Close LH rear door
    참고

    Do not latch
42. Open LH front door
    참고

    Use caution while working around this area not to damage any components
43. Install both LH front inner HV battery bolts hand tight
    참고

    2x bolts, EP20, 136 Nm, Torque at later step

    

    

44. Close LH front door
    참고

    Do not latch
45. Open RH rear door
    참고

    Use caution while working around this area not to damage any components
46. Remove HV battery alignment rod from RH rear inner bolt location
    참고

    1x rod

    

47. Install RH rear inner battery bolt hand tight
    참고

    1x bolt, 16mm, 66 Nm, Lift up LH rear main carpet for access, Torque at later step

    

48. Install RH inner HV battery bolt hand tight
    참고

    1x bolt, 16mm, 66 Nm, Torque at later step

    

49. Close RH rear door
50. Open RH front door
    참고

    Use caution while working around this area not to damage any components
51. Install both RH front inner HV battery bolts hand tight
    참고

    2x bolts, EP20, 136 Nm, Torque at later step

    

    

52. Close RH front door
    참고

    Do not latch
53. Lower vehicle onto pack completely
    참고

    Recommend assistance
54. Torque RH bolts securing HV battery to vehicle
    참고

    8x bolts, 13mm, 35 Nm

    

55. Torque LH bolts securing HV battery to vehicle
    참고

    8x bolts, 13mm, 35 Nm

    

56. Torque bolts securing RH front support bracket to vehicle
    참고

    4x bolts, 16mm, 110 Nm

    

57. Torque bolts securing LH front support bracket to vehicle
    참고

    4x bolts, 16mm, 110 Nm

    

58. Torque central bolts securing HV battery through center ski cover
    참고

    4x bolts, EP14, 34 Nm

    

59. Raise vehicle and lower onto locks, then remove battery table from under vehicle
    참고

    Recommend assistance, Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

60. Position support stand to support front section of rear subframe

    

61. Remove bolt securing LH side of rear subframe to body
    참고

    1x bolt, 21mm, 130 Nm, Discard after removal

    

62. Install bolt and shear plate to LH side of rear subframe hand tight
    참고

    1x bolt, 21mm, 130 Nm, Torque at later step

    

63. Install bolts securing LH rear shear plate to body hand tight
    참고

    2x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles. Torque at later step.

    

64. Torque bolt securing subframe and LH rear shear plate to body
    참고

    1x bolt, 21mm, 130 Nm, Mark bolt after torque

    

    

65. Torque small fasteners securing LR rear shear plate to body
    참고

    2x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles.

    

66. Remove bolt securing RH side of rear subframe to body
    참고

    1x bolt, 21mm, 130 Nm, Discard after removal

    

67. Install bolt and shear plate to RH side of rear subframe hand tight
    참고

    1x bolt, 21mm, 130 Nm, Torque at later step

    

68. Install bolts securing RH shear plate to HV battery hand tight
    참고

    2x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles. Torque at later step.

    

69. Torque bolt securing subframe and RH rear shear plate to body
    참고

    1x bolt, 21mm, 130 Nm

    

70. Torque small fasteners securing RH rear shear plate to body
    참고

    2x bolts, 13mm, 35 Nm for non-Structural Pack vehicles, 62 Nm for Structural Pack vehicles.

    

71. Remove support stand from under vehicle

    

72. Install clips securing coolant hoses to RH shear plate
    참고

    2x fir tree clips

    

73. Install clips securing coolant hoses to LH shear plate
    참고

    2x fir tree clips

    

74. Connect RDU HV cable to HV battery
    참고

    1x connector, Make sure the connector lock is 90 degrees from the connector before beginning to secure the connector, Use one hand to support the connector while other latching locking tab. Once installed, verify that the latch is not damaged and fully secured in the latched position

    

    

75. Install nut securing RDU HV cable bracket to HV battery
    참고

    1x nut, 10mm, 10 Nm

    

76. Position coolant drain underneath RH rear of HV battery
77. Remove hose plugs and connect coolant outlet hose to rear PT return hose
    참고

    1x spring clip, Perform push-pull-push test to make sure hose is fully seated, Use shop towel to clean any coolant residue if necessary

    

    

78. Position coolant drain container underneath LH rear of HV battery
79. Remove plugs and connect RDU inverter inlet hose to rear of HV battery
    참고

    1x spring clip, Perform push-pull-push test to make sure hose is fully seated

    

    

80. Remove coolant drain container from underneath vehicle
81. Position rear battery enclosure skid plate to HV battery for installation

    

82. Install upper bolts securing rear battery enclosure skid plate to HV battery hand tight
    참고

    4x bolts, 13mm, 35 Nm, Torque at later step

    

83. Install upper nut securing rear battery enclosure skid plate hand tight
    참고

    1x nut, 10mm, 13 Nm, Torque at later step

    

84. Install lower bolts securing HV battery rear skid plate enclosure
    참고

    2x bolts, EP10, 13 Nm, Torque at later step, Earlier vins may be equipped with additional bolts

    

85. Torque bolts securing HV battery and rear skid plate to vehicle
    참고

    4x bolts, 13mm, 35 Nm

    

86. Torque upper nut securing rear battery enclosure skid plate
    참고

    1x nut, 10mm, 13 Nm

    

87. Install lower bolts securing HV battery rear skid plate enclosure
    참고

    2x bolts, EP10, 13 Nm, Torque at later step, Earlier vins may be equipped with additional bolts

    

88. Install RH side hose clips to rear battery skid plate
    참고

    2x fir tree clips

    

89. Install LH side hose clip to HV battery rear skid plate enclosure
    참고

    2x clips, Clip quantity may vary on older vehicles

    

90. Apply Loctite 222 onto mid aero shield bolts and install mid aero shield
    참고

    11x bolts, 10mm, 5 Nm, Fasteners may vary, Model Y Structural Pack will one less bolt and one extra clip

    

91. Position coolant drain container underneath LH front of HV battery

    

92. Remove plugs then connect HV battery coolant return hose
    참고

    1x spring clip, 2x plugs, Perform push-pull-push test to make sure hose is fully seated

    

    

93. Position coolant drain container below HV battery manifold hose

    

94. Remove plugs then connect HV battery front manifold coolant hose
    참고

    1x spring clip, 2x plugs, Perform push-pull-push test to make sure hose is fully seated

    

    

95. Install HV battery front manifold hose clips to body
    참고

    2x clips, Newer vehicles may be equipped with 1x clip

    

96. Position coolant drain container underneath RH front of HV battery
97. Remove plugs then connect PT supply hose
    참고

    1x spring clip, 1x hose clip, 2x plugs, Perform push-pull-push test to make sure hose is fully seated

    

    

98. Remove plugs and connect PT return hose
    참고

    1x spring clip, 1x hose clip, 2x plugs, Perform push-pull-push test to make sure hose is fully seated

    

    

99. Remove coolant drain container from underneath vehicle
100. Connect both AC compressor HV harness connectors on HV battery
     참고

     2x locking connectors, 2 stage locking connector, After the connector is seated and there is an audible click, Engage the second lock by pressing towards the connector

     

101. Install front skid plate onto HV battery
     참고

     2x tabs, Slide tabs onto front of HV battery

     

     

     

102. Install the bolts securing the front skid plate to the HV battery
     참고

     4x bolts, E10, 13 Nm

     

103. Release LH front wheel liner from bungee strap
     참고

     Remove strap from vehicle

     

104. Install LH front wheel liner to HV battery and lower wheel well area
     참고

     3x clips, 1x bolt, 10mm, 5 Nm

     

     

105. Release RH front wheel liner from bungee strap
     참고

     Remove strap from vehicle

     

106. Install RH front wheel liner to HV battery and lower wheel well area
     참고

     3x clips, 1x bolt, 10mm, 5 Nm

     

     

107. Position the front aero shield to vehicle and install nuts
     참고

     2x nuts, 15mm, 5 Nm

     

108. Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield
     참고

     7x bolts, 10mm, 5 Nm

     

109. Lower vehicle partially and set onto locks
     참고

     Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
110. Open all four doors
     참고

     Latch rear doors to prevent accidental closure
111. Install positive 12V output
     참고

     1x nut, 13mm, 9 Nm, Install new nut, Make sure rubber boot is not pinched between cable terminal and pass through

     

112. Install positive 12V output cover to PCS cable
     참고

     1x cover

     

113. Install nut securing DCDC ground strap to HV battery
     참고

     1x nut, 13mm, 15 Nm, Install new nut

     

114. Remove logic cap and connect the HVC logic connector
     참고

     1x connector, 1x cap, Align connector then pull the handle to locking position get connector fully seated

     

     

115. Clean busbar HV connector contact surface of residual Penetrox
     참고

     Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar

     

116. Clean HV connector contact surface of residual Penetrox
     참고

     Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector

     

117. Apply Penetrox onto HV connector joints
     참고

     Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered

     

     

118. Position busbar kit connector and lower onto HV header

     

119. Install bolts securing charge port busbar kit to HV Header
     참고

     2x bolts, 10mm, 9 Nm

     

120. Inspect HV insulating gloves
     참고

     Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves. https://service.teslamotors.com/protected-doc/ServiceBulletins/External/TN/TN-15-92-003_High_Voltage_Awareness_Care_Points_R4.pdf

     

121. Put on HV insulating gloves and leather over gloves
     참고

     Make sure to wear Electrical Protective Gloves any time Hioki tester is used

     

122. Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
     참고

     2x HV joints, The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step

     

123. Remove HV insulating gloves
124. Install fastener securing busbar cover access door
     참고

     1x bolt, 10mm, 9 Nm

     

125. Connect logic connector at LH 60 seat frame
     참고

     1x connector

     

126. Install clip securing logic connector harness to LH seat frame
     참고

     1x clip

     

127. Remove coolant bottle cap

     

128. Inspect coolant level and top off as necessary
     참고

     Ensure that the fluid level is at the Max line

     

129. Connect first responder loop and 12V negative terminal
     참고

     1x nut, 10mm, 6 Nm, 1x connector, Engage locking tab, Connect FRL first before connecting 12V to avoid damage to car computer

     

     

130. Press and hold park button to release EPB service mode
     참고

     Remove wheel chocks if necessary

     

     

131. f
132. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN-COOLANTvia Toolbox: (link)via Service Mode Plus:
     • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Start Fluid Fill/Drain
     • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Start Fluid Fill/Drain
     • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Start Fluid Fill/Drain
     • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Start Fluid Fill/Drain
     • Drive Unit ➜ Front Drive Unit Replacement ➜ Start Coolant Fill/Drain
     • Drive Unit ➜ Rear Drive Unit Replacement ➜ Start Coolant Fill/Drain
     참고

     This will ensure the octovalve is in the Series position, Coolant pumps will also be disabled, Once run is selected routine is in progress despite the prompt with loading circle, Routine will time out after several hours and return valves to parallel position if unattended, Select 'X' at top right of window to close once complete
133. Place empty coolant container into front storage area

     

134. Fill container with at least 15L of coolant

     

135. Place filled coolant container into front storage area

     

136. Close air inlet and coolant refill valves

     

     

137. Install vacuum refill cap onto coolant bottle assembly

     

138. Setup vacuum refill tool
     참고

     Verify all valves on refill tool are in the closed position, See image for clarity

     

     

139. Install vacuum refill hose into refill cap on coolant bottle
     참고

     Perform push-pull-push test to verify hose is fully installed

     

140. Place end of overflow hose into empty container

     

141. Place refill hose inside filled coolant container
     참고

     Make sure hose end is fully submerged into coolant

     

     

142. Connect shop air supply to coolant refill tool
     참고

     If not already done, Verify refill valve is set to off

     

143. Open air inlet valve to draw a vacuum, Once gauge stabilizes, Fully close valve
     참고

     Gauge stabilizes roughly (60-70 cmHg), Vacuum should not drop after the valves are closed

     

     

144. Slowly open the refill valve to allow coolant to be drawn into the system
     참고

     Make sure hose end of refill hose is fully submerged during entire process

     

145. Once the gauge reads zero, close the refill valve

     

     

146. Slowly open the coolant refill valve to allow coolant to be drawn into the system
     참고

     Make sure end of coolant refill hose is fully submerged during entire process

     

147. Monitor gauge for 30 seconds to verify a vacuum is maintained in the cooling system

     

148. Reopen the air inlet valve for 3 minutes to continue evacuating cooling system, then close valve

     

     

149. Disconnect shop air supply from coolant refill tool

     

150. Remove coolant refill hose from coolant container

     

151. Remove coolant overflow hose from coolant container

     

152. Remove vacuum refill hose from refill cap on coolant bottle

     

153. Remove coolant refill tool from vehicle

     

     

154. Remove both coolant containers from inside underhood area

     

155. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
     • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
     • Thermal ➜ Coolant System ➜ Coolant Purge Start
     via Service Mode Plus:
     • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
     • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
     • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
     • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
     • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
     • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
156. Inspect coolant level and top off as necessary
     참고

     Ensure that the fluid level is at the Max line

     

157. Install coolant bottle cap

     

158. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
     • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
     • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
     • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
     • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
     • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
     • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
     참고

     Select ‘X’ at top right of window to close once complete.
159. Fill brake bleeder reservoir to full level

     

160. Clean area around brake fluid reservoir and remove brake reservoir cap

     

161. Top off brake fluid reservoir
     참고

     Top off brake fluid as needed

     

162. Install pressure bleeder adapter onto reservoir

     

163. Set brake bleed reservoir pressure to 30 psi
     참고

     Connect power supply to bleeder and turn on the power, Set pressure to 30 psi, Attach brake bleed reservoir to brake bleed adapter

     

     

164. Remove bleeding valve covers and install the fluid catching bottle to LH front brake caliper outer bleeding valve before starting the ESP
     참고

     2x covers

     

     

165. Open LH front brake caliper outer bleeding valve.
166. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEEDvia Toolbox: (link)via Service Mode:
     • Chassis ➜ Brakes ➜ Brake Bleed FL-RR
     • Chassis ➜ Brakes ➜ Brake Bleed FL-RR
167. Close the bleeding valve once the pump stop running, then repeat the process for inner bleeding valve, and then lastly repeat the process for outer bleeding valve again
     참고

     2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers

     

168. Repeat the above step till clear fluid and no air bubbles come out of the LH front brake caliper bleeding valve
     참고

     2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers

     

169. Remove the fluid catching bottle, Torque LH front brake caliper bleeding valves then install covers
     참고

     2x covers, 2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers

     

     

170. Remove bleeding valve covers and install the fluid catching bottle to RH front brake caliper outer bleeding valve before starting the ESP
     참고

     2x covers

     

     

171. Open RH front brake caliper outer bleeding valve.
172. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEEDvia Toolbox: (link)via Service Mode:
     • Chassis ➜ Brakes ➜ Brake Bleed FR-RL
     • Chassis ➜ Brakes ➜ Brake Bleed FR-RL
173. Close the bleeding valve once the pump stop running, then repeat the process for inner bleeding valve, and then lastly repeat the process for outer bleeding valve again
     참고

     2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers

     

174. Repeat the above step till clear fluid and no air bubbles come out of the RH front brake caliper bleeding valves
     참고

     2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers

     

175. Remove the fluid catching bottle, Torque RH front brake caliper bleeding valves and install covers
     참고

     2x covers, 2x bleeding valves, 11mm, 18.5 Nm (+/- 2 Nm) Base and Plus calipers

     

     

176. Remove bleeding valve cover and install the fluid catching bottle to RH rear brake caliper bleeding valve before starting the ESP
     참고

     1x cover

     

     

177. Open RH rear brake caliper bleeding valve.
178. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEEDvia Toolbox: (link)via Service Mode:
     • Chassis ➜ Brakes ➜ Brake Bleed FL-RR
     • Chassis ➜ Brakes ➜ Brake Bleed FL-RR
179. Close the bleeding valve once the pump stop running
     참고

     1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper

     

     

180. Repeat the above step till clear fluid and no air bubbles come out of the RH rear brake caliper bleeding valve
     참고

     1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper

     

181. Remove the fluid catching bottle, Torque RH rear brake caliper bleeding valve and install cover
     참고

     1x cover, 1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper

     

182. Remove bleeding valve cover and install the fluid catching bottle to LH rear brake caliper bleeding valve before starting the ESP
     참고

     1x cover

     

     

183. Open LH rear brake caliper bleeding valve
184. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEEDvia Toolbox: (link)via Service Mode:
     • Chassis ➜ Brakes ➜ Brake Bleed FR-RL
     • Chassis ➜ Brakes ➜ Brake Bleed FR-RL
185. Close the bleeding valve once the pump stop running
     참고

     1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper

     

     

186. Repeat the above step untill clear fluid and no air bubbles come out of the LH rear brake caliper bleeding valve
     참고

     1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper

     

187. Remove the fluid catching bottle, Torque LH rear brake caliper bleeding valve and install cover
     참고

     1x cover, 1x bleeding valve, 11mm, 10 Nm (+/- 3 Nm) Base caliper, 14 Nm (+/- 2 Nm) Plus caliper

     

     

188. Power off brake bleed reservoir and detach brake bleed reservoir from brake bleed adapter

     

     

189. Remove pressure bleeder adapter from reservoir

     

190. Check fluid level
     참고

     Top off if necessary

     

191. Install brake reservoir cap

     

192. Pump the brake pedal a few times to ensure the brake pedal feels normal
193. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST_BRAKE_X_STIFFNESS-TEST-SERVICEvia Toolbox: (link)via Service Mode: Chassis ➜ Brakes ➜ Brake Stiffness Test
     참고

     Do not press the brake pedal during the test.
194. Close all four doors
     참고

     If 12V is powered up, Unlatch rear doors before closing
195. Raise vehicle partially and lower lift onto locks
     참고

     Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
196. Install all four wheels
     참고

     5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
197. Lower vehicle until tires are touching the ground
     참고

     Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
198. Torque all four wheels
     참고

     5x nuts, 21mm, 175 Nm
199. Install all four wheel caps
     참고

     1x cap, Align valve stem with wheel cap cavity
200. Install rear apron
     참고

     14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips

     

     

201. Close hood
202. Remove vehicle from lift
     참고

     Lower rack arms fully and remove from under vehicle
203. Get into driver seat and slowly reverse vehicle enough to allow clearance for all four doors open
     참고

     Adjust driver seat if needed
204. Open all four doors
     참고

     Latch rear doors to prevent accidental closure
205. Torque LH rear inner HV battery bolt
     참고

     1x bolt, 16mm, 66 Nm, Located below LH rear main carpet

     

206. Torque RH rear inner battery bolt
     참고

     1x bolt, 16mm, 66 Nm, Located below RH rear main carpet for access

     

207. Remove object positioned beneath rear cabin carpet

     

208. Install clips securing rear main cabin carpet to vehicle
     참고

     3x push clips

     

209. Install clip securing RH lower B-pillar to body
     참고

     1x push clip, Clip goes through B-pillar and rear cabin carpet

     

210. Install RH rear sill trim
     참고

     5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of RH rear sill trim into trunk side trim and work your way forward securing clips

     

     

211. Reseat RH rear door seal
     참고

     Seat pillar and sill trim tabs underneath seal

     

212. Install clip securing LH lower B-pillar to body
     참고

     1x push clip, Clip secures lower B-pillar and rear cabin carpet to body

     

213. Install LH rear sill trim
     참고

     5x clips, Rear edge is mated with groove in trunk side trim, Install rear edge of LH rear sill trim into trunk side trim and work your way forward securing clips, Trim part may slightly differ, by vehicle build location

     

     

214. Reseat LH rear door seal
     참고

     Seat pillar and sill trim tabs underneath seal

     

215. Install 2nd row seat cushion
     참고

     1x connector, Slide rear cushion rearward then align foam with seat rail, Make sure cushion is fully seated with push & pull test

     

     

     

216. Torque LH middle inner HV battery bolt
     참고

     1x bolt, 16mm, 66 Nm

     

217. Fold LH side of rear main carpet to its original position

     

218. Torque RH middle inner HV battery bolt
     참고

     1x bolt, 16mm, 66 Nm

     

219. Fold RH side of rear main carpet to its original position

     

220. Install 2nd row floor mat into vehicle

     

221. Torque both RH forward HV battery bolts
     참고

     2x bolts, EP20, 136 Nm

     

     

222. Install RH front cabin carpet support access plugs
     참고

     2x plugs, Newer Vins may be equipped with 1x foam plug

     

     

223. Fold the RH front main cabin carpet back to original position

     

224. Install clip securing RH front cabin carpet to body
     참고

     1x clip

     

225. Install RH lower A-pillar trim
     참고

     6x clips, 2x locating pins, Align front locating pin first

     

226. Install clip securing RH lower A-pillar trim
     참고

     1x clip

     

227. Install RH mid A-pillar assembly
     참고

     1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Make sure the seal seat on top of the trim

     

228. Install RH IP end cap
     참고

     3x clips

     

229. Install RH console side panel carpet
     참고

     12x clips, 2x locating pins, Position side panel and align the front locator, then the rear locator, Push side panel towards console to install

     

     

230. Install RH front floor mat

     

231. Connect the RH footwell assembly connectors
     참고

     2x connectors

     

232. Install clips securing RH footwell assembly
     참고

     4x push clips, 2x connectors, Puddle lamp and speaker

     

233. Move RH front seat to original position

     

234. Torque both LH front inner HV battery bolts
     참고

     2x bolts, EP20, 136 Nm

     

     

235. Install LH front cabin carpet support access plugs
     참고

     2x plugs, Newer vins may be equipped with 1x foam plug

     

     

236. Fold the LH front main cabin carpet back to original position

     

237. Install clip securing LH front cabin carpet to body

     

238. Install LH console side panel carpet
     참고

     11x clips, 2x locating pins, Position side panel and align the front into front locator, then the rear locator, Push side panel towards console to install

     

     

     

     

239. Install LH front floor mat

     

240. Install connectors to LH footwell cover and position for installation
     참고

     3x tabs, 1x Ethernet connector, 1x puddle light connector

     

     

     

241. Install screw and clips securing LH footwell cover
     참고

     1x screw, T20, 2.5 Nm, 2x push clips

     

242. Install LH lower A-pillar trim
     참고

     6x clips, 2 locating pins, Align front locating pin first

     

243. Install clip securing LH lower A-pillar trim
     참고

     1x push clip

     

244. Install LH mid A-pillar assembly
     참고

     1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim

     

245. Install LH IP end cap
     참고

     3x clips

     

246. Move LH front seat to original position
247. Raise all four windows
248. Close all four doors
     참고

     If 12V is powered up, Unlatch rear doors before closing
249. Remove lift pad adapters from RH rocker
     참고

     2x lift pad adapters

     

     

250. Install butyl patches onto RH rocker access holes
     참고

     2x butyl patches, Apply pressure along patch to verify fully secured to body, Replace with new patch if needed, Roughly 2" x 2 1/2"

     

     

251. Install RH rocker carrier onto body
     참고

     10x clips

     

252. Install bolts securing RH rocker carrier to body
     참고

     2x bolts, 10mm, 5 Nm

     

     

253. Install RH rocker panel onto RH rocker carrier
     참고

     11x clips, 11x tabs, Recommend assistance, Tabs go into cavities on the rocker carrier and cannot be accessed from outer side of trim

     

254. Install clips securing RH rocker cover to front and rear wheel liner
     참고

     4x push clips

     

     

255. Remove lift pad adapters from LH rocker
     참고

     2x lift pad adapters

     

     

256. Install butyl patches onto LH rocker access holes
     참고

     2x butyl patches, Apply pressure along patch to verify fully secured to body, Replace with new patch if needed, Roughly 2" x 2 1/2"

     

     

257. Install LH rocker carrier onto body
     참고

     10x clips

     

258. Install bolts securing LH rocker carrier to body
     참고

     2x bolts, 10mm, 5 Nm

     

     

259. Install LH rocker panel onto LH rocker carrier
     참고

     11x clips, 11x tabs, Recommend assistance, Tabs go into cavities on the rocker carrier and cannot be accessed from outer side of trim

     

260. Install clips securing LH rocker cover to front and rear wheel liner
     참고

     4x push clips

     

     

261. Perform a road test and ensure proper brake pedal feel and performance
     참고

     Per current FRT (00040100)