2020-12-16

Recliner Actuator - Seat Back - 2nd Row - RH (Remove and Replace)

Correction code 13053402 0.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

토크 규격

표 1. Torque Specifications: Recliner Actuator - Seat Back - 2nd Row - RH (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
액추에이터 팬을 LH 2열 시트 프레임에 고정하는 볼트
2.5 Nm (1.8 lbs-ft)
  • 10mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 2인치 익스텐션
Reuse
액추에이터 팬에서 LH 2열 시트 등받이 리클라이너 액추에이터를 고정하는 나사
2.5 Nm (1.8 lbs-ft)
  • 8mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse

Remove

  1. RH 2열 시트 등받이를 탈거합니다. Seat Back - 2nd Row - RH (Remove and Replace)
  2. RH 2열 시트 등받이를 수직으로 세우고 어셈블리를 안전하고 안정적인 작업 공간에 놓습니다.
  3. RH 2열 내부 B커버를 탈거합니다. B-Cover - Inner - 2nd Row - RH (Remove and Replace)을(를) 참조하십시오.
  4. 내부 피벗 장치를 시트에 고정하는 클립을 탈거한 다음 시트에서 피벗 장치를 당겨 어셈블리에서 탈거합니다.
  5. RH 2열 시트 프레임 클립에서 액추에이터 케이블을 분리한 다음 시트 프레임 래치에서 케이블이 떨어지게 위로 들어서 시트 프레임에서 분리합니다.
  6. RH 시트 리클라인 하네스 커넥터를 연결 해제합니다.
  7. 액추에이터 팬을 RH 2열 시트 프레임에 고정하는 볼트를 탈거합니다.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 2인치 익스텐션
  8. 액추에이터 팬에서 LH 2열 시트 등받이 리클라이너 액추에이터를 고정하는 나사를 탈거합니다.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    • 8mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

Install

Installation procedure is the reverse of removal.