2023-12-26

Trim - Cushion - Front Passenger Seat (Remove and Replace)

Correction code 13072302 0.78 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-12-01: 끊긴 링크를 수정했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Seat base edges are sharp and can cause personal injury. Wear cut resistant gloves when removing the seat from the vehicle, and while performing procedures that involve work on or near the seat base.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Remove

  1. 펌웨어가 버전 2023.2.11 이상인지 확인합니다. 펌웨어 버전이 2023.2.11 이상이 아닌 경우 차량 펌웨어를 업데이트합니다.
  2. 차량에서 전면 동승석 시트를 탈거합니다. 참조 항목: Seat Assembly - 1st Row - LH (Remove and Replace).
  3. 전면 동승석 시트 외측 사이드 실드를 탈거합니다. 참조 항목: Side Shield - Outboard - Driver Seat (Remove and Replace).
  4. 전면 동승석 시트 내측 사이드 실드를 탈거합니다. 참조 항목: Side Shield - Inboard - Driver Seat (Remove and Replace).
  5. 시트를 젖혀 등받이로 지지되도록 하여 시트 쿠션 아래쪽에 접근할 수 있도록 합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    필요한 경우 시트 쿠션을 손상되지 않도록 보호합니다.
  6. 쉘 에이프런을 시트 밑면에 고정하는 클립을 분리합니다.
  7. 열선 패드 전기 커넥터를 연결 해제합니다.
  8. 열선 패드 커넥터를 앞으로 밀어 시트 하단에서 분리합니다.
  9. 시트 쿠션 열선 패드를 모듈에서 연결 해제합니다.
  10. 시트 쿠션 열선 패드 커넥터를 시트 등받이 헤드 패드 커넥터에서 분리합니다.
  11. 시트 쿠션 커넥터를 위로 밀어 시트 어셈블리에서 분리합니다.
  12. 시트 착석 센서 커넥터를 연결 해제합니다.
  13. 시트 탑승 센서를 시트 밑면에 고정하는 클립을 분리한 후, 시트 밑면에서 센서를 분리합니다.
  14. 시트 쿠션 발포체를 시트 서스펜션에 고정하는 클립(2개)를 분리합니다.
  15. 시트 쿠션 폼을 시트 쿠션 프레임 전면, 안쪽, 바깥쪽에 고정하는 클립 스트립(3개)을 분리한 후, 프레임에서 폼을 분리합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    시트 쿠션 히터 매트 커넥터와 시트 착석 센서 어셈블리가 시트 서스펜션 또는 프레임에 걸리지 않게 합니다.
  16. 시트를 수직 위치로 되돌립니다.
  17. 똑바로 들어 올려 쿠션 패드 어셈블리를 시트 프레임 어셈블리에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    열선 패드 및 시트 착석 센서 하네스가 시트 프레임에서 떨어져 있는지 확인합니다.
  18. 시트 쿠션 트림을 폼 패드에 고정하는 스트랩을 분리합니다.
  19. 시트 쿠션 트림을 폼 패드에 고정하는 클립(x18)을 탈거한 다음 폼 패드에서 트림을 탈거합니다.

Install

  1. 시트 쿠션 트림을 폼 패드에 배치한 다음 시트 쿠션 트림을 폼 패드에 고정하는 클립(18개)을 다시 장착합니다.
  2. 시트 쿠션 트림을 폼 패드에 고정하는 스트랩을 고정합니다.
  3. 장착을 위해 쿠션 패드 어셈블리를 시트 쿠션 프레임에 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    시트 쿠션의 후면을 시트 하단 프레임에 삽입한 다음 시트 쿠션의 나머지 부분을 시트 하단 프레임으로 내립니다. 배선 하네스가 시트 프레임의 뒷면을 통과하여 배선되었는지 확인합니다.
  4. 시트를 젖혀 등받이로 지지되도록 하여 시트 쿠션 아래쪽에 접근할 수 있도록 합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    필요한 경우 시트 쿠션을 손상되지 않도록 보호합니다.
  5. 시트 쿠션 폼 패드를 시트 쿠션 프레임에 장착한 다음 시트 쿠션을 프레임 전면, 안쪽, 바깥쪽에 고정하는 클립 스트립(3개)을 조입니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    시트 히터 커넥터와 시트 탑승 센서 어셈블리가 시트 서스펜션 또는 프레임을 통과하지 않게 합니다.
  6. 시트 쿠션을 시트 서스펜션에 고정하는 클립(2개)을 조입니다.
  7. 시트 쿠션 열선 패드를 모듈에 연결합니다.
  8. 시트 쿠션 커넥터를 시트 어셈블리에 장착합니다.
  9. 시트 쿠션 열선 패드 커넥터를 시트 등받이 헤드 패드 커넥터에 연결합니다.
  10. 열선 패드 커넥터를 시트 프레임에 장착합니다.
  11. 열선 패드 커넥터를 연결합니다.
  12. 시트 밑면에 시트 탑승 센서를 장착한 후, 센서를 시트 밑면에 고정하는 클립을 조입니다.
  13. 착석 센서 커넥터를 연결합니다.
  14. 시트를 수직 위치로 이동합니다.
  15. 전면 동승석 시트 내측 사이드 실드를 장착합니다. 참조 항목: Side Shield - Inboard - Driver Seat (Remove and Replace).
  16. 전면 동승석 시트 외측 사이드 실드를 장착합니다. 참조 항목: Side Shield - Outboard - Driver Seat (Remove and Replace).
  17. 전면 동승석 시트를 차량에 장착합니다. 참조 항목: Seat Assembly - 1st Row - LH (Remove and Replace).
  18. If servicing the front passenger seat in a North American vehicle:
    1. Remove all objects from the front passenger seat before beginning calibration.
    2. On the vehicle touchscreen, touch Controls (Vehicle Icon) > Software and check the vehicle firmware version. If the vehicle firmware is 2023.2.11 or newer, perform a software reinstall. See Software Reinstall - Touchscreen. If the vehicle firmware is not 2023.2.11 or newer, update the vehicle firmware. See Software Update.
    3. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
    4. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
    5. In Toolbox, click on the Actions tab, and then search for "OCS".
    6. Run the PROC_OCS1P_SELF-CALIBRATIONvia Toolbox: (link)via Service Mode Plus: Safety & Restraints ➜ Seats ➜ OCS1P Self Capacitance Calibration routine.
    7. Click on the Actions tab, and then search for "Seat calibration".
    8. Run the PROC_VCRIGHT_SEAT-CALIBRATEvia Toolbox: (link)via Service Mode Plus: Low Voltage ➜ Seats ➜ Calibrate routine.
    9. Disconnect Toolbox and remove the laptop from the vehicle.