2024-02-04

Bracket - Compressor (Remove and Replace)

Correction code 18203202 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Torque Specifications

표 1. Torque Specifications: Bracket - Compressor (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
A/C 컴프레서 브래킷을 A/C 컴프레서에 고정하는 볼트
9 Nm (6.6 lbs-ft)
  • 10mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
HV 하네스 브래킷을 A/C 컴프레서에 고정하는 볼트
9 Nm (6.6 lbs-ft)
  • 13mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
접지 스트랩을 A/C 컴프레서에 고정하는 볼트
7 Nm (5.2 lbs-ft)
  • 10mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
A/C 컴프레서 어셈블리를 스트럿 타워 브레이스에 고정하는 볼트
31 Nm (22.9 lbs-ft)
  • 10mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse

Remove

  1. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  2. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  3. 차량 전기 절연 절차를 수행합니다. 참조 항목: Vehicle HV Disablement Procedure.
  4. 펜더 보호용 커버를 팬 슈라우드 및 프렁크 지지대에 배치합니다.
  5. 12V 보조 배터리를 탈거합니다. 참조 항목: 12V/LV Battery (Remove and Replace).
  6. 12V 배터리 브래킷에서 후면 배터리 타이다운 스트랩을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    12V 배터리 브래킷은 A/C 컴프레서 브래킷으로도 작동합니다.
  7. 12V 배터리 통풍구 튜브를 12V 배터리 브래킷에 고정하는 클립을 풉니다.
  8. 냉각수 호스를 12V 배터리 브래킷에 고정하는 클립(4개)을 풉니다.
  9. 커넥터 잠금 탭을 푼 다음 A/C 컴프레서에서 저전압 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  10. A/C 컴프레서 저전압 하네스를 A/C 컴프레서 HV 하네스 브래킷에 고정하는 클립을 분리합니다.
  11. HV 하네스 브래킷을 A/C 컴프레서에 고정하는 볼트를 탈거합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  12. 접지 스트랩을 A/C 컴프레서에 고정하는 볼트를 탈거한 다음 접지 스트랩을 한쪽으로 치워둡니다.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  13. 접지 스트랩 고정 지점 근처에서 냉각수 호스를 A/C 컴프레서 브래킷에 고정하는 클립을 분리합니다.
  14. A/C 컴프레서 HV 하네스를 스트럿 타워 서포트 브레이스에 고정하는 클립을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    HV 하네스를 당기지 마십시오.
  15. 커넥터 잠금 탭을 푼 다음 LH 전면 스트럿 타워 근처에 있는 HVIL 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  16. A/C 컴프레서에서 A/C 컴프레서 HV 커넥터 검은색 잠금 탭을 당겨 분리합니다.
  17. 45도 픽(쪼는) 도구를 사용하여 외측 잠금 탭을 당기는 동시에 중앙 잠금 탭을 누르고 A/C 컴프레서에서 HV 커넥터를 탈거합니다.
  18. HV 하네스 브래킷을 앞과 위로 이동하여 A/C 컴프레서에서 브래킷을 분리한 다음 브래킷을 주의하여 한쪽으로 치워둡니다.
  19. 보조 작업자와 함께 A/C 컴프레서 어셈블리를 스트럿 타워 브레이스에 고정하는 볼트를 탈거한 다음 A/C 컴프레서 어셈블리를 펜더 보호용 커버에 주의하여 놓습니다.
    31 Nm (22.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  20. A/C 컴프레서 브래킷을 A/C 컴프레서에 고정하는 볼트를 탈거한 다음 컴프레서에서 브래킷을 탈거합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:

Install

  1. A/C 컴프레서 브래킷을 A/C 컴프레서에 배치한 다음 브래킷을 컴프레서에 고정하는 볼트(3개)를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  2. 블로우건을 사용하여 A/C 컴프레서 브래킷을 전면 스트럿 타워 서포트 브레이스에 고정하는 데 사용했던 볼트 구멍을 청소합니다.
  3. 보조 작업자가 스트럿 타워 브레이스 아래에서 A/C 컴프레서 어셈블리를 지지하는 동안 A/C 컴프레서 어셈블리를 브레이스에 고정하는 볼트를 손으로 조인 다음 토크로 조입니다.
    31 Nm (22.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  4. A/C 컴프레서 HV 하네스 브래킷을 A/C 컴프레서에 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    HV 하네스 브래킷이 표시된 대로 A/C 컴프레서 상단부의 하네스 마운트에 체결되는지 확인합니다.
  5. A/C 컴프레서 HV 커넥터를 A/C 컴프레서에 완전히 안착시킨 다음 잠금 탭을 A/C 컴프레서를 향해 밀어 체결합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the connector is fully attached.
  6. A/C 컴프레서 HV 하네스를 스트럿 타워 서포트 브레이스에 고정하는 클립을 장착합니다.
  7. LH 전면 스트럿 타워 근처에 있는 HVIL 커넥터를 연결한 다음 잠금 탭을 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  8. 접지 스트랩 고정 지점 근처에서 냉각수 호스를 A/C 컴프레서 브래킷에 고정하는 클립을 장착합니다.
  9. 접지 스트랩을 A/C 컴프레서에 배치한 다음 접지 스트랩을 A/C 컴프레서에 고정하는 볼트를 장착합니다.
    7 Nm (5.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  10. HV 하네스 브래킷을 A/C 컴프레서에 고정하는 볼트를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
  11. A/C 컴프레서 저전압 하네스를 A/C 컴프레서 HV 하네스 브래킷에 고정하는 클립을 장착합니다.
  12. 저전압 전기 커넥터를 A/C 컴프레서에 연결한 다음 잠금 탭을 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  13. 냉각수 호스를 A/C 컴프레서 브래킷에 고정하는 클립(4개)을 장착합니다.
  14. 후면 배터리 타이다운 스트랩을 12V 배터리 브래킷에 장착합니다.
  15. 12V 배터리 통풍구 튜브를 12V 배터리 브래킷에 고정하는 클립을 장착합니다.
  16. 12V 보조 배터리를 장착합니다. 참조 항목: 12V/LV Battery (Remove and Replace).
  17. 차량에서 펜더 보호용 커버를 제거합니다.
  18. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  19. 2열 하단 시트 쿠션을 장착합니다. 참조 항목: Seat Cushion - Lower - 2nd Row (Remove and Replace).
  20. 12V 전원을 다시 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  21. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).