2025-06-27

Glass - Backlight (Remove and Replace)

Correction code 10204102 1.92 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-12-10: 장착 전 글라스 검사 서비스 요구 사항에 대한 새로운 주의 사항을 추가했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Wear appropriate personal protective equipment (PPE) including cut-resistant gloves and safety glasses when performing this procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
For Europe only: Only technicians who have been trained in working with diisocyanates and have completed all required certification courses are permitted to perform procedures using urethane and other products containing diisocyanates. Proper personal protective equipment (PPE) must be worn when working with products containing diisocyanates.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
New glass components (windshield, roof, door, and fixed glass) must be inspected before installation to meet Tesla’s internal standards of quality. Perform the inspection described in 장착 전 글라스 검사 before beginning this procedure.
  • 볼 핀 해머: 1115198-00-A
  • Equalizer 360: 1080598-00-A
  • WRD Spider 3 - 1571168-00-A
  • 휴대용 스탠드: 1054720-00-A
  • 밸러스트 백: 1145158-00-A
  • 이중 흡착 컵 핸들: 1080599-00-A
  • 간격/단차 측정 도구: 1588904-00-A
  • 코킹 및 접착제 건: 1080593-00-A

Remove

  1. 리프트게이트 상단 트림을 탈거합니다. Trim - Upper - Liftgate (Remove and Replace)을(를) 참조하십시오.
  2. 리프트게이트 하단 트림을 탈거합니다. Trim - Liftgate - Lower (Remove and Replace)을(를) 참조하십시오.
  3. LH FM 안테나 앰프에서 전기 커넥터를 연결 해제합니다.
  4. RH FM 안테나 앰프에서 전기 커넥터를 연결 해제합니다.
  5. 리프트게이트 글라스에서 LH 안테나 필터 전기 커넥터를 연결 해제합니다.
  6. 리프트게이트 글라스에서 RH 안테나 필터 전기 커넥터를 연결 해제합니다.
  7. CHMSL 전기 커넥터를 연결 해제합니다.
  8. 백라이트 글라스의 LH 및 RH에 이중 흡착 컵을 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    흡착 컵의 성능을 높이려면 흡착 컵 아래의 글라스를 닦아냅니다.
  9. 리프트게이트를 엽니다.
  10. 볼 핀 해머 및 개스킷 스크래퍼 또는 이에 준하는 도구를 사용하여 백라이트 글라스 상단의 양쪽 기준점을 파쇄합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    이 단계를 수행할 때는 보안경을 포함한 적절한 PPE를 착용하십시오.
  11. 볼 핀 해머 및 Equalizer 360 또는 이에 준하는 도구를 사용하여 백라이트 글라스 상단의 양쪽 H 클립을 파쇄합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    이 단계를 수행할 때는 보안경을 포함한 적절한 PPE를 착용하십시오.
    Informational PurposesAn informational icon, calling your attention
    TIp
    얇은 하이드로블레이드 부착물 사용을 고려하고 글라스 세정제로 윤활하십시오.
  12. WRD Spider 3 글라스 탈거 키트를 준비합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • WRD Spider 3 - 1571168-00-A
  13. 와이어를 스타터 공구에 고정한 다음 백라이트 글라스 후면 모서리의 접착 비드를 통해 차량 내부에서 스타터 공구를 삽입합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    스타터 공구를 사용하는 동안 가드를 사용하여 후면 데크 패널 손상을 방지하십시오.
  14. 라인을 당깁니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    글라스 둘레를 감쌀 수 있을 만큼 충분히 라인을 당겨야 합니다. 와이어의 양쪽 끝은 차량 내부에 남아 있을 수 있으며 완전히 당겨야 합니다.
  15. 고정 지점을 백라이트 글라스 어셈블리의 내부에 고정한 다음, 라인을 앵커에 고정합니다.
  16. 라인의 내부 면을 Spider 절단 도구에 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Spider 도구의 지침을 따릅니다. 절단 도구의 개구부를 통과해 라인을 집어넣고 매듭을 묶어 라인을 제자리에 고정합니다. 스핀들이 올바른 방향으로 회전하지 않는 경우 절단 도구가 손상됩니다.
  17. Spider 절단 도구를 백라이트 글라스 어셈블리의 내부 면에 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    절단 라인의 방향을 기록합니다. 라인이 큰 풀리를 감싸고 90도 각도를 유지하는지 확인하십시오.
  18. 앵글 드라이버를 전기 드릴에 고정합니다.
  19. 드릴로 절단 도구의 스핀들을 돌려 백라이트 글라스 어셈블리 탈거를 시작합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    라인을 90도 각도에 가깝게 유지하며 필요에 따라 절단 도구를 이동합니다.
  20. 보조 작업자와 함께 백라이트 글라스를 차량에서 탈거합니다.
  21. 면도날을 조심스럽게 사용하여 리프트게이트 차체에서 남은 우레탄을 모두 제거합니다. 우레탄 잔여물 두께가 1mm 이하인지 확인하십시오.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    이 단계를 수행할 때는 절단 방지 장갑을 포함한 적절한 PPE를 착용하십시오.
  22. 차체에서 파쇄한 기준점, H 클립 및 기타 모든 파편을 제거합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    정비소 에어건을 사용하여 파편을 불어내는 경우 보안경을 포함한 적절한 PPE를 착용하십시오.
  23. 차체 접합면을 IPA 천으로 닦아냅니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    CHMSL에서 눈에 보이는 얼룩, 지문 또는 기타 모든 표시를 제거합니다.

Install

  1. 새 백라이트 글라스의 LH 및 RH에 이중 흡착 컵을 고정합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    흡착 컵의 성능을 높이려면 흡착 컵 아래의 글라스를 닦아냅니다.
  2. 보조 작업자와 함께 백라이트 글라스를 임시로 장착할 수 있도록 배치합니다.
  3. 백라이트 글라스와 차체의 간격 및 단차를 점검합니다. 조정이 필요한 경우 기록합니다.
  4. 보조 작업자와 함께 차량에서 백라이트 글라스를 탈거하고 안쪽이 위를 향하도록 받침대에 놓습니다.
  5. CHMSL 어셈블리를 새 백라이트 글라스에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    CHMSL이 고정될 때까지 CHMSL을 H 클립에 고르게 밀어 넣습니다.
  6. 차량에서 우레탄 도포 경로를 따라 그리고 백라이트 글라스를 탈거하는 중 손상된 영역에 우레탄 프라이머를 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    계속하기 전에 프라이머가 건조되도록 2분 이상 기다립니다.
  7. 우레탄 카트리지의 팁을 대략 너비 8mm, 높이 13mm의 삼각형 모양으로 절단하여 코킹 건과 우레탄을 준비합니다.
  8. 프라이머 경로를 따라 백라이트 글라스에 우레탄을 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    간격이 있는 모든 부분에 채워넣고 우레탄의 돌출부가 없도록 일정한 비드를 만듭니다.
  9. 보조 작업자와 함께 백라이트 글라스를 차량에 장착합니다.
  10. 백라이트 글라스와 차체의 간격 및 단차를 점검하고 필요에 따라 조정합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    백라이트 글라스 장착 상태를 조정하는 데 트림 도구 및 모래 주머니를 사용할 수 있습니다.
  11. 리프트게이트를 열기 전에 글라스가 건조되도록 10분 이상 기다립니다.
  12. 백라이트 글라스에서 이중 흡착 컵을 탈거하고 리프트게이트를 엽니다.
  13. CHMSL 전기 커넥터를 연결합니다.
  14. RH 안테나 필터 전기 커넥터를 연결합니다.
  15. LH 안테나 필터 전기 커넥터를 연결합니다.
  16. RH FM 안테나 앰프 전기 커넥터를 연결합니다.
  17. LH FM 안테나 앰프 전기 커넥터를 연결합니다.
  18. 리프트게이트 하단 트림을 장착합니다. Trim - Liftgate - Lower (Remove and Replace)을(를) 참조하십시오.
  19. 리프트게이트 상단 트림을 장착합니다. Trim - Upper - Liftgate (Remove and Replace)을(를) 참조하십시오.
  20. 리프트게이트를 닫습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Do not drive the vehicle until the adhesive manufacturer’s recommended minimum drive-away time has passed. Dow Betaseal Express has a drive-away time of 1 hour minimum in temperatures of 0˚F (-18˚C) or warmer. If necessary, leave the tape applying pressure to the glass on the vehicle and advise the customer that they can remove it after 24 hours. Additionally, advise the customer that they should avoid high driving speeds and speed bumps for the next 24 hours.
  21. 차량에 후면 성에 제거 장치와 관련된 경고가 있는 경우 다음 추가 단계를 수행하여 후면 성에 제거 장치를 다시 활성화합니다.
    1. Toolbox 3가 설치된 노트북을 차량에 연결합니다. Toolbox 3(연결 및 연결 해제)을(를) 참조하십시오.
    2. Toolbox에서 Actions 탭을 클릭하고 검색 필드에 "Defrost"를 입력한 다음 PROC_VCRIGHT_REAR_DEFROST-RE-ENABLEvia Toolbox: (link)via Service Mode: Closures ➜ Windows ➜ Re-Enable을(를) 클릭하고 Run을 클릭한 다음 루틴이 완료될 때까지 기다립니다.
    3. Toolbox 3가 설치된 노트북을 차량에서 연결 해제합니다. Toolbox 3(연결 및 연결 해제)을(를) 참조하십시오.