2024-06-25

Charge Port (CCS) (Remove and Replace)

Correction code 44011652 0.90 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2024-02-01: 액추에이터 팬 및 모터, 차량 전기 절연 절차에 대한 단계를 삭제했습니다.
  • 2023-10-27: 차체 쪽 충전 포트(CP) 볼트 토크를 9Nm으로 업데이트합니다.
  • 2023-07-10: 액추에이터 팬 및 모터에 대한 단계를 추가하고 차량 절연 절차 단계를 다시 추가했습니다.
  • 2023-05-25: 차량 전기 절연 절차를 충전 포트 전압 점검 절차로 대체했습니다.
  • 1076921-00-B 절연 멀티미터, Fluke 1507(북미)
  • 1076927-00-A Hioki RM 3548
  • 1108272-00-B 캡, 로직 연결, 인버터, 3DU
  • 1130480-00-A 테스트 프로브, 슬림, Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

이 절차를 수행하려면 적합한 개인 보호 장비(PPE)가 필요합니다.

  • 고전압(HV) 절연 장갑
  • 가죽 장갑 보호구
  • 고전압 장갑 테스터
  • 보안경
  • 전기 위험 등급 안전 장화
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

HV 장갑 사용 기한이 만료되지 않았는지 확인하십시오. HV 장갑의 사용 기한은 장갑에 인쇄된 테스트 날짜로부터 최대 12개월이며, 장갑의 사용 기한이 12개월 기간 내에 있더라도 최초 사용일로부터 6개월간만 사용해야 합니다.

Torque Specifications

표 1. Torque Specifications: Charge Port (CCS) (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
충전 포트 버스바 리드를 충전 포트 어셈블리에 연결하는 너트
9 Nm (6.6 lbs-ft)
  • 10mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
충전 포트(CP)를 차량에 고정하는 볼트
9 Nm (6.6 lbs-ft)
  • 10mm 딥소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse

Remove

  1. 모든 도어를 열고 모든 창문을 내립니다.
  2. 전면 시트를 앞으로 이동합니다.
  3. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  4. HEPA 필터 어셈블리를 탈거합니다. 참조 항목: Assembly - Filter - HEPA (Remove and Install).
  5. 충전 포트 도어를 엽니다.
  6. 리프트게이트를 엽니다.
  7. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  8. 충전 포트 전압 점검 절차를 수행합니다. 참조 항목: Charge Port Voltage Check.
  9. LH 하단 C필러 트림을 탈거합니다. 참조 항목: Trim - C-Pillar - Lower - LH (Remove and Replace).
  10. 후면 트렁크 적재함 바닥을 탈거합니다. 참조 항목: Trunk Load Floor - Rear (Remove and Replace).
  11. 전면 트렁크 적재함 바닥을 탈거합니다. 참조 항목: Trunk Load Floor - Front (Remove and Replace).
  12. 트렁크 실 트림을 탈거합니다. 참조 항목: Trim - Sill - Trunk (Remove and Replace).
  13. LH 트렁크 적재함 바닥 브래킷을 탈거합니다. 참조 항목: Bracket - Trunk Load Floor - LH (Remove and Replace).
  14. LH 트렁크 포켓 브래킷을 탈거합니다. 참조 항목: Bracket - Trunk Pocket - LH (Remove and Replace).
  15. LH 트렁크 사이드 트림을 탈거합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  16. LH 상단 C필러 트림을 탈거합니다. 참조 항목: Trim - C-Pillar - Upper - LH (Remove and Replace).
  17. LH C필러 브래킷을 탈거합니다. 참조 항목: Bracket - C-Pillar - LH (Remove and Replace).
  18. 흰색 잠금 탭을 탈거한 다음 충전 포트(CP)에서 로직 커넥터를 연결 해제합니다.
    그림 1. Model 3에서 본 모습, Model Y도 유사함
  19. 잠금 탭을 위쪽으로 누른 다음 충전 포트(CP)에서 3상 커넥터를 연결 해제합니다.
    그림 2. Model 3에서 본 모습, Model Y도 유사함
  20. 픽 공구를 사용하여 안전 캡을 버스바 브래킷에 고정하는 탭(2개)을 부드럽게 분리한 다음 안전 캡을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    안전 캡이 손상될 수 있으므로 과도하게 힘을 주어 벌리지 마십시오.
  21. 충전 포트 버스바 리드를 충전 포트 어셈블리에 고정하는 너트(2개)를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  22. 잠금 탭을 푼 다음 충전 포트 액추에이터에서 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  23. 커넥터 잠금 장치를 해제한 다음, 테일라이트 커넥터에서 전기 하네스를 분리합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    물 유입으로 인해 테일라이트를 교체해야 하는 경우 작업용 타월을 테일라이트 커넥터 아래에 배치하여 다른 전기 구성품에 대한 손상을 방지하십시오.
  24. 충전 포트(CP)를 차량에 고정하는 볼트를 탈거한 다음 충전 포트(CP)를 차량에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

Install

  1. 나중에 이 절차에서 저항을 측정하는 것에 대비하여 Hioki 저항계의 영점 조정을 수행합니다. 참조 항목: Resistance Meter (Zero Adjust).
  2. 동일한 충전 포트(CP)를 다시 장착하는 경우: 충전 포트 어셈블리 후면의 충전 포트 버스바 HV 헤더를 IPA 천으로 닦은 다음 1분 동안 건조시킵니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트(CP)에 전기 접합부 컴파운드가 미리 도포되어 있으므로, 새 충전 포트 어셈블리를 장착할 경우 이 단계를 건너뜁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    플라스틱 트림 공구를 사용하여 IPA 천을 충전 포트 버스바 HV 헤더의 틈새에 밀어 넣습니다.
  3. 충전 포트(CP)를 차량에 배치한 다음 충전 포트(CP)를 차량에 고정하는 볼트를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하네스가 제대로 배선되었는지 확인하고, 케이블타이가 있는 접착 패드가 장착된 경우 올바르게 장착되어 있는지 확인합니다.
  4. 전기 커넥터를 충전 포트 액추에이터에 연결한 다음 잠금 탭을 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  5. 동일한 충전 포트(CP)를 다시 장착하는 경우: 충전 포트(CP) 뒤쪽 버스바 스터드의 토크 점검을 수행합니다.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트 어셈블리를 장착하는 경우 이 단계를 건너뜁니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T10 비트
    • 4인치 익스텐션
    • 래칫/토크 렌치
  6. IPA 천을 사용하여 충전 포트 버스바 리드에서 잔류물 및 잔해를 모두 닦은 다음 1분 동안 자연 건조시킵니다.
    그림 3. 버스바 브래킷 디자인이 다를 수 있음
  7. 동일한 충전 포트(CP)를 다시 장착하는 경우: 각 충전 포트 버스바 리드(2개)에서 충전 포트(CP)와 접촉하는 면에 전기 접합부 컴파운드를 두 방울씩 도포합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    새 충전 포트(CP)에 전기 접합부 컴파운드가 미리 도포되어 있으므로, 새 충전 포트 어셈블리를 장착할 경우 이 단계를 건너뜁니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    접촉면이 전기 접합부 컴파운드로 완전히 덮였는지 확인합니다.
    그림 4. 버스바 브래킷 디자인이 다를 수 있음
  8. 충전 포트 버스바를 충전 포트(CP)에 배치한 다음 버스바 리드를 충전 포트(CP)에 고정하는 너트(2개)를 장착합니다.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 딥소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  9. HV 절연 장갑과 가죽을 덧댄 장갑을 착용합니다.
  10. 충전 포트(CP)에서 Hioki 저항계를 사용하여 충전 포트 버스바 리드와 충전 포트 버스바 스터드 사이의 저항을 측정합니다. 다른 리드 및 스터드에서도 이 테스트를 수행합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    허용 가능한 저항은 0.050mΩ(50μΩ)~0.270mΩ(270μΩ)입니다. 측정된 저항이 0.270mΩ(270μΩ)을 초과하면 고전압 조인트에 저항이 너무 많은 것입니다. 필요에 따라 패스너를 탈거하고 이소프로필 알코올로 해당 부위를 청소한 후 패스너를 다시 장착하고 다시 테스트합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    저항이 0.050mΩ(50μΩ) 미만일 때에는 프로브를 재배치하고 다시 측정합니다. 4회 시도 후 저항이 일정하게 0.050mΩ(50μΩ) 미만이면 테스트가 통과한 것이므로 다음 단계를 계속합니다.
  11. HV 절연 장갑과 가죽을 덧댄 장갑을 벗습니다.
  12. 두 개의 잠금 탭 체결 여부를 확인하면서 버스바 브래킷에 안전 캡을 장착합니다.
  13. 충전 포트(CP)에 3상 커넥터를 연결한 다음 잠금 탭을 아래로 밉니다.
    그림 5. Model 3에서 본 모습, Model Y도 유사함
  14. 전기 하네스를 테일라이트 커넥터에 연결한 다음 커넥터 잠금 장치를 체결합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    커넥터에 빨간색 잠금 탭이 있는 경우: Push the red locking tab into the connector to engage the connector lock.
  15. 충전 포트(CP)에 로직 커넥터를 연결한 다음 흰색 잠금 탭을 장착합니다.
    그림 6. Model 3에서 본 모습, Model Y도 유사함
  16. LH C필러 브래킷을 장착합니다. 참조 항목: Bracket - C-Pillar - LH (Remove and Replace).
  17. LH 상단 C필러 트림을 장착합니다. 참조 항목: Trim - C-Pillar - Upper - LH (Remove and Replace).
  18. LH 트렁크 사이드 트림을 장착합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  19. LH 트렁크 포켓 브래킷을 장착합니다. 참조 항목: Bracket - Trunk Pocket - LH (Remove and Replace).
  20. LH 적재함 바닥 브래킷을 장착합니다. 참조 항목: Bracket - Trunk Load Floor - LH (Remove and Replace).
  21. 트렁크 실 트림을 장착합니다. 참조 항목: Trim - Sill - Trunk (Remove and Replace).
  22. 전면 트렁크 적재함 바닥을 장착합니다. 참조 항목: Trunk Load Floor - Front (Remove and Replace).
  23. 후면 트렁크 적재함 바닥을 장착합니다. 참조 항목: Trunk Load Floor - Rear (Remove and Replace).
  24. LH 하단 C필러 트림을 장착합니다. 참조 항목: Trim - C-Pillar - Lower - LH (Remove and Replace).
  25. 12V 전원을 다시 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  26. HEPA 필터 어셈블리를 장착합니다. 참조 항목: Assembly - Filter - HEPA (Remove and Install).
  27. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  28. 차량 소프트웨어를 다시 설치합니다. 참조 항목: Software Reinstall - Touchscreen.