2025-12-03

Headlights and Fog Lights (Check Aiming using LET Tool) (Inspection)

교정 코드 17400800619 0.24 바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-11-20: Released new procedure.

Special tools required for this procedure:

Supplier Part Number Description
Tesla 1133367-00-B LET Headlight Machine SLA 40

Identify Headlight Type

The SAE/ECE headlight (1) has a different reflector and lens design compared to the Global headlight (2), illustrated below.

Headlight and Fog Light Inclination

Factory specification for headlight and fog light inclination is -1%. Check local regulations for your country's tolerance. The factory headlight and fog light inclination value is stamped on the light's housing, but not always easy to see. See images for reference.
그림 1. Inclination value stamped on headlight
그림 2. Inclination value stamped on headlight (zoomed in)
그림 3. Inclination value stamped on fog light

Check Headlight and Fog Light Aiming

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
When checking the aiming of the headlights, do not set the vehicle to the "Adjust Headlights" mode through the touchscreen. The "Adjust Headlights" mode creates a non-standard headlight beam pattern that should not be used for checking the aiming of the headlights.
  1. Park the vehicle on a flat and level surface.
  2. Make sure that the tire pressures are set to specification.
  3. Open the hood.
  4. Power on the headlight tester.
  5. Position the headlight aimer perpendicular to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use the visor/laser to line up the tester perpendicular to the axis between the hood struts. If the headlight aimer can move between the LH and RH headlights while maintaining the same laser angle projected onto the hood struts, it is set correctly (perpendicular) to the vehicle.
  6. Latch the LH front door.
    Informational PurposesAn informational icon, calling your attention
    참고
    Latching the LH front door prevents the headlights and/or fog lights from shutting off during the procedure.
  7. Turn on the headlights.
  8. Select the "eye" icon on the LET headlight aimer, and then select the left headlight icon.
  9. Select height to 0.8-1.0m.
  10. Position the headlight aimer in front of the LH headlight.
  11. Move the headlight aiming machine following the black arrows on the screen. Once the machine is centered to the headlight, selecting the "X" button will direct you to the aiming screen.

    Non-Global Headlight Beam

    Global Headlight Beam

  12. Note down the headlight "Y" and "H" values in the internal notes in SCA.
  13. Position the headlight aimer in front of the RH headlight, and then repeat steps 11 and 12 for the RH headlight.
  14. Position the headlight aimer in front of the LH fog light.
  15. Turn on the fog lights.
  16. Cover both headlights.
  17. Set up the headlight aimer for the LH fog light: select the "Adjust" (screwdriver) icon, and then select the LH fog light icon.
    Informational PurposesAn informational icon, calling your attention
    참고
    When selecting the "eye" (check) icon, fog lights cannot be selected.
  18. Select the height to <0.8m.
  19. Move the headlight aiming machine following the black arrows on the screen. Once the machine is centered to the fog light, selecting the "X" button will direct you to the aiming screen.
  20. Note down the fog light "Y" and "H" values in the internal notes in SCA.
  21. Position the headlight aimer in front of the RH fog light.
  22. Repeat steps 19 and 20 for the RH fog light.
  23. Turn off the fog lights, and then set the headlights to AUTO.
  24. Unlatch the LH front door.
  25. If the headlight and/or fog light aiming values are out of specification, adjust the headlights and/or fog lights. See one of the following sections: