2023-08-03

Track - Outer - Front Passenger Seat (Remove and Replace)

Correction code 13013002 0.66 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices. NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure.NOTE: See 인체공학적 주의 사항for safe and healthy working practices.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.

Remove

  1. 펌웨어가 버전 2023.2.11 이상인지 확인합니다. 펌웨어 버전이 2023.2.11 이상이 아닌 경우 차량 펌웨어를 업데이트합니다.
  2. 차량에서 전면 동승석 시트를 탈거합니다. Seat Assembly - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  3. 전면 동승석 시트 외측 사이드 실드를 탈거합니다. Side Shield - Outboard - Driver Seat (Remove and Replace)을(를) 참조하십시오.
  4. 전면 동승석 시트 바깥쪽 골반 프리텐셔너를 탈거합니다. Pretensioner - Outboard Lap - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  5. 시트 어셈블리에서 프리텐셔너 하네스 클립(3개)을 분리합니다.
  6. 시트를 젖혀 등받이로 지지되도록 하여 시트 쿠션 아래쪽에 접근할 수 있도록 합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    필요한 경우 시트 쿠션을 손상되지 않도록 보호합니다.
  7. RH 1열 시트 트랙 위치 센서를 탈거합니다. Sensor - Position - Track - 1st Row Seat - RH (Remove and Replace)을(를) 참조하십시오.
  8. 높이 모터 전기 커넥터를 연결 해제합니다.
  9. 트랙 모터 하네스를 트랙 모터 하우징에 고정하는 클립을 분리합니다.
  10. 트랙 모터 전기 커넥터를 연결 해제합니다.
  11. 높이 모터 어셈블리를 시트 쿠션 프레임에 고정하는 볼트를 탈거하여 폐기합니다.
    23 Nm (17.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
  12. 높이 모터 어셈블리를 후면 RH 링크에 고정하는 볼트를 탈거하여 폐기합니다.
    18 Nm (13.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T45 소켓
  13. 리프트 모터 어셈블리를 배선 하네스에서 아래로 밀고 바깥쪽으로 빼내 시트 어셈블리에서 탈거합니다.
  14. 전면 동승석 시트 외측 트랙을 시트 어셈블리에 고정하는 볼트를 탈거하여 폐기합니다.
    23 Nm (17.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
  15. 트랙 브리지 어셈블리에서 전면 동승석 시트 외측 트랙을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    브리지 택 모터 탭을 들어 올린 다음, 외측 트랙을 밀어 분리합니다.
  16. 전면 동승석 시트 외측 트랙을 트랙 브리지 어셈블리에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    트랙 모터 케이블은 정사각형으로 맞물려 있으며 외측 트랙과 정렬되어야 합니다. 필요에 따라 케이블을 손으로 돌려 정렬합니다. 트랙 모터 브리지가 완전히 안착할 때까지 외측 트랙 안으로 밀어 넣습니다.

Install

  1. 전면 동승석 시트 외측 트랙을 시트 어셈블리에 고정하는 새 볼트를 장착합니다.
    23 Nm (17.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
  2. 트랙 모터 하네스를 트랙 모터 하우징에 고정하는 클립을 장착합니다.
  3. 트랙 모터 전기 커넥터를 연결합니다.
  4. 장착을 위해 높이 모터 어셈블리를 시트 쿠션 프레임에 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    모터 어셈블리를 적합한 각도로 장착하여 시트 하단 하네스가 걸리지 않도록 합니다.
  5. 높이 모터 어셈블리를 후면 RH 링크에 고정하는 새 볼트를 장착합니다.
    18 Nm (13.3 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T45 소켓
  6. 높이 모터 어셈블리를 시트 쿠션 프레임에 고정하는 새 볼트를 장착합니다.
    23 Nm (17.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T50 소켓
  7. 높이 모터 전기 커넥터를 연결합니다.
  8. RH 1열 시트 트랙 위치 센서를 장착합니다. Sensor - Position - Track - 1st Row Seat - RH (Remove and Replace)을(를) 참조하십시오.
  9. 시트를 정상적인 수직 위치로 되돌립니다.
  10. 전면 동승석 시트 외측 골반 프리텐셔너를 장착합니다. Pretensioner - Outboard Lap - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  11. 안전벨트 프리텐셔너 하네스 클립(3개)을 장착합니다.
  12. 전면 동승석 시트 외측 사이드 실드를 장착합니다. Side Shield - Outboard - Driver Seat (Remove and Replace)을(를) 참조하십시오.
  13. 차량에 전면 동승석 시트를 장착합니다. Seat Assembly - 1st Row - LH (Remove and Replace)을(를) 참조하십시오.
  14. If servicing the front passenger seat in a North American vehicle:
    1. Remove all objects from the front passenger seat before beginning calibration.
    2. On the vehicle touchscreen, touch Controls (Vehicle Icon) > Software and check the vehicle firmware version. If the vehicle firmware is 2023.2.11 or newer, perform a software reinstall. See Software Reinstall - Touchscreen. If the vehicle firmware is not 2023.2.11 or newer, update the vehicle firmware. See Software Update.
    3. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
    4. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
    5. In Toolbox, click on the Actions tab, and then search for "OCS".
    6. Run the PROC_OCS1P_SELF-CALIBRATIONvia Toolbox: (link)via Service Mode Plus: Safety & Restraints ➜ Seats ➜ OCS1P Self Capacitance Calibration routine.
    7. Click on the Actions tab, and then search for "Seat calibration".
    8. Run the PROC_VCRIGHT_SEAT-CALIBRATEvia Toolbox: (link)via Service Mode Plus: Low Voltage ➜ Seats ➜ Calibrate routine.
    9. Disconnect Toolbox and remove the laptop from the vehicle.