2025-10-17

Valve Body - EXV - Supermanifold (Remove and Replace)

Correction code 18401302 0.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2025-10-07: LV 배터리를 다시 연결하는 중복된 단계를 삭제했습니다.
  • 2023-04-05: A/C 오일 규격에 대한 유액 및 용량을(를) 참조하여 사용할 A/C 오일 유형을 업데이트했습니다.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Model Y thermal management components operate under very tight specifications and can malfunction if Service procedures are not carefully followed. DO NOT rely on past experience with other thermal management systems; read through the Service Manual and do not deviate from the instructions.
Informational PurposesAn informational icon, calling your attention
참고
This procedure requires the A/C Refrigerant (Recovery and Recharge) procedure to be performed. If not already automatically added to the Service Visit, add correction code 18200102 as a separate activity to the Service Visit.

Torque Specifications

표 1. Torque Specifications: Valve Body - EXV - Supermanifold (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
슈퍼매니폴드-컴프레서 A/C 라인을 슈퍼매니폴드에 고정하는 볼트
22 Nm (16.2 lbs-ft)
  • 13mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  • 6인치 익스텐션
Reuse
확장 밸브 바디
19 Nm (14.0 lbs-ft)
  • 1588745-00-A - 팽창 밸브 소켓, 28mm, 1/2" 드라이브
  • 6인치 익스텐션
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
n/a

Remove

  1. AC 장비를 설정합니다.
  2. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  3. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_VCFRONT_X_START-THERMAL-FILL-DRAINvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Start Thermal Fill/Drain
    • Thermal ➜ Coolant System ➜ Start Coolant Fill/Drain
    • Thermal ➜ Refrigerant System ➜ Start Refrigerant Fill/Drain
    via Service Mode Plus: Drive Inverter ➜ Front Drive Inverter Replacement ➜ Start Fluid Fill/Drain
    Informational PurposesAn informational icon, calling your attention
    참고
    완료되면 창 오른쪽 상단에 있는 "X"를 선택하여 닫습니다. 열 오일 주입/배출 루틴의 시간 제한은 5시간입니다. 5시간 후에는 EXV가 종료되며 루틴을 다시 수행해야 합니다. 차고 > 열 > 냉매 루프 EXV를 통해 EXV 위치가 열려 있는지 확인하고, LCC, CC 좌측, Evap, CC 우측, 냉각 장치가 모두 ~100%인지 확인합니다. 재순환 장치는 ~20%이며, LCC 솔레노이드는 개방되어 있습니다.
  4. 12V 전원을 분리합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. 냉매 시스템을 복구합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge).
  6. 슈퍼매니폴드-컴프레서 A/C 라인을 슈퍼매니폴드에 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 6인치 익스텐션
  7. 슈퍼매니폴드에서 슈퍼매니폴드-컴프레서 A/C 라인을 탈거한 다음 S자형 후크를 사용하여 후드 내 보관 유닛 지지대에 겁니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    오일이 떨어지지 않도록 라인을 주의하여 배치하십시오.
  8. 커넥터 잠금 장치를 분리한 다음 원하는 EXV로 이어지는 전기 커넥터를 연결 해제합니다. 예제 이미지의 연결 해제 순서를 따르십시오.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
    Informational PurposesAn informational icon, calling your attention
    참고
    연결 해제 순서는 접근을 쉽게 하기 위한 것입니다.
    그림 1. 연결 해제 순서
  9. 잠금 탭을 분리한 다음 원하는 EXV에서 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
    그림 2. 이베퍼레이터 EXV 표시됨
  10. 슈퍼매니폴드에서 슈퍼매니폴드 하네스를 탈거하여 프렁크 지지대에 놓습니다.
  11. 픽 도구를 사용하여 잠금 탭을 아래쪽으로 당긴 다음 차량 전면을 향해 당겨 EXV 코일을 탈거합니다.
  12. 슈퍼매니폴드에서 EXV 밸브 바디를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 1588745-00-A - 팽창 밸브 소켓, 28mm, 1/2" 드라이브
    • 6인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

Install

  1. 적절한 유형의 A/C 오일로 EXV 나사산 및 O링을 윤활합니다. A/C 오일 규격은 유액 및 용량을(를) 참조하십시오. 그런 다음 밸브를 슈퍼매니폴드에 손으로 조이기 시작합니다.
  2. EXV를 슈퍼매니폴드에 규격 토크로 완전히 조입니다.
    19 Nm (14.0 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 1588745-00-A - 팽창 밸브 소켓, 28mm, 1/2" 드라이브
    • 6인치 익스텐션
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  3. EXV 코일을 EXV에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    커넥터 어셈블리의 잠금 탭을 EXV의 홈에 정렬합니다.
  4. 탈거 중 연결 해제했던 전기 커넥터를 연결한 다음 커넥터 잠금 장치를 체결합니다.
  5. 새 씰 와셔를 슈퍼매니폴드-컴프레서 A/C 라인의 슈퍼매니폴드 쪽에 장착한 다음 소량의 적절한 유형의 A/C 오일로 와셔를 윤활합니다. A/C 오일 규격은 유액 및 용량을(를) 참조하십시오.
  6. 슈퍼매니폴드-컴프레서 A/C 라인을 슈퍼매니폴드에 배치한 다음 A/C 라인을 슈퍼매니폴드에 고정하는 볼트를 손으로 조입니다.
  7. A/C 라인을 슈퍼매니폴드에 고정하는 볼트를 조입니다.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 13mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
    • 6인치 익스텐션
  8. A/C 시스템을 재충전합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge).
  9. 응급구조대 루프를 연결하고 12V 음극 단자를 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  10. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
  11. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST-SELF_VCFRONT_X_HEAT-PUMP-COMMISSIONINGvia Toolbox: (link)via Service Mode: Thermal ➜ Refrigerant System ➜ Run Heat Pump Commissioningvia Service Mode Plus: Drive Inverter ➜ Front Drive Inverter Replacement ➜ Heatpump commissioning
    Informational PurposesAn informational icon, calling your attention
    참고
    Thermal Drain/Fill 모드에 진입한 후 이 루틴이 실행되지 않는 경우 AC 컴프레서 작동이 차단됩니다. 완료되면 창 오른쪽 상단에 있는 'X'를 선택하여 닫습니다.
  12. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    Informational PurposesAn informational icon, calling your attention
    참고
    완료되면 창 오른쪽 상단에 있는 'X'를 선택하여 닫습니다.
  13. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST-SELF_VCRIGHT_X_HVAC-PERFORMANCEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Test HVAC Performance
    • Thermal ➜ HVAC ➜ HVAC Performance Test
    • Thermal ➜ Actions ➜ Test HVAC Performance
  14. 정비 모드를 종료합니다. 참조 항목: Service Mode.
  15. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).