2023-10-27

Safety Cap - Busbar - Charge Port to HV Battery (Remove and Replace)

Correction code 440151020.36 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2023-10-10: 충전 포트 도어를 수동으로 닫지 않도록 하라는 주의 사항을 추가했습니다.
  • 1076921-00-A 절연 멀티미터, Fluke 1587(유럽/중동/아프리카)
  • 1076921-01-B 절연 멀티미터, Fluke 1508(APAC)
  • 1130480-00-A 테스트 프로브, 슬림, Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

이 절차를 수행하려면 적합한 개인 보호 장비(PPE)가 필요합니다.

  • 고전압(HV) 절연 장갑
  • 가죽 장갑 보호구
  • 고전압 장갑 테스터
  • 보안경
  • 전기 위험 등급 안전 장화
Warning IconA warning icon, calling your attention to a possibly risky situation
경고

장갑 팽창 장치는 HV 장갑을 테스트하기 위해서 유일하게 권장되는 방법입니다. 이 절차를 시작하기 전에 오른쪽과 왼쪽 HV 장갑 모두 테스트를 통과해야 합니다. 어느 한쪽 장갑이 공기 점검 테스트를 통과하지 못하면 양쪽 장갑을 모두 폐기하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
Make sure that the HV gloves are not expired.
  • North America: HV gloves can be used up to 12 months after the testing date printed on the glove, but only 6 months after first use even if the gloves are still within the 12 month period. If the gloves were not put into service during the 12-month period following the testing date, they must be retested before being put into service.
  • Europe: Class 0 (1000V) HV gloves have no expiration date and may be used if they pass the pre-use assessment and the periodic inspection.
  • Asia Pacific: Follow the expiration date stated by the HV glove manufacturer, and:
    • o China only: Test the gloves every 6 months according to GB/T 17622.

Remove

  1. 모든 창문을 내립니다.
  2. 모든 도어를 열고 후면 도어를 걸쇠로 고정합니다.
  3. 리프트게이트를 엽니다.
  4. 후드를 엽니다.
  5. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  6. 충전 포트 도어를 엽니다.
  7. 12V 전원을 연결 해제합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  8. 충전 포트 전압 점검 절차를 수행합니다. 참조 항목: Charge Port Voltage Check.
  9. 후면 트렁크 바닥 트림을 탈거합니다. 참조 항목: Trunk Load Floor - Rear (Remove and Replace).
  10. 전면 트렁크 플로어 트림을 탈거합니다. 참조 항목: Trunk Load Floor - Front (Remove and Replace).
  11. 트렁크 실 트림을 탈거합니다. 참조 항목: Trim - Sill - Trunk (Remove and Replace).
  12. LH 트렁크 적재함 바닥 브래킷을 탈거합니다. 참조 항목: Bracket - Trunk Load Floor - LH (Remove and Replace).
  13. LH 트렁크 포켓 브래킷을 탈거합니다. 참조 항목: Bracket - Trunk Pocket - LH (Remove and Replace).
  14. LH 트렁크 사이드 트림을 탈거합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  15. LH 상단 C필러 트림을 차량에 고정하는 클립(6개) 및 탭(1개)을 분리한 다음 트림을 한쪽으로 치워 둡니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    헤드라이너에서 LH 상단 C필러 트림의 맨 앞 부분을 주의하여 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    LH 상단 C 필러 트림은 후면 안전벨트에 여전히 고정되어 있습니다.
  16. C필러 브래킷을 탈거합니다. 참조 항목: Bracket - C-Pillar - LH (Remove and Replace).
  17. 충전 포트 저전압 커넥터에서 잠금 탭을 분리한 다음 충전 포트(CP)에서 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    검은색 커넥터 탭을 부드럽게 들어 올려 12핀 저전압 커넥터에서 하얀색 잠금 탭을 탈거합니다.
  18. 충전 포트 어셈블리에서 충전 포트 버스바 안전 캡을 탈거합니다.

Install

  1. 충전 포트 버스바 안전 캡을 충전 포트 어셈블리에 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 단계를 수행하기 전에는 충전 포트 버스바 안전 캡이 고정되지 않습니다.
  2. 저전압 하네스를 충전 포트에 연결한 다음 잠금 탭을 장착합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    하얀색 잠금 탭이 검은색 커넥터 탭에 잠길 때까지 12핀 저전압 커넥터에 주의하여 삽입합니다.
  3. C필러 브래킷을 장착합니다. 참조 항목: Bracket - C-Pillar - LH (Remove and Replace).
  4. LH 상단 C필러 트림을 차량에 배치한 다음 트림을 차량에 고정하는 클립(6개) 및 탭(1개)을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    C필러 트림 전면부의 상단 그루브를 헤드라이너와 정렬합니다.
  5. LH 트렁크 사이드 트림을 장착합니다. 참조 항목: Trim - Side - Trunk - LH (Remove and Replace).
  6. LH 트렁크 포켓 브래킷을 장착합니다. 참조 항목: Bracket - Trunk Pocket - LH (Remove and Replace).
  7. LH 적재함 바닥 브래킷을 장착합니다. 참조 항목: Bracket - Trunk Load Floor - LH (Remove and Replace).
  8. 트렁크 실 트림을 장착합니다. 참조 항목: Trim - Sill - Trunk (Remove and Replace).
  9. 전면 트렁크 플로어 트림을 장착합니다. 참조 항목: Trunk Load Floor - Front (Remove and Replace).
  10. 후면 트렁크 바닥 트림을 장착합니다. 참조 항목: Trunk Load Floor - Rear (Remove and Replace).
  11. 12V 전원을 다시 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  12. 리프트게이트를 닫습니다.
  13. 충전 포트 도어를 닫습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    충전 포트 도어를 수동으로 닫지 않도록 하십시오.
  14. 래치를 풀고 모든 도어를 닫습니다.