2020-12-16

Armrest - 2nd Row (Remove and Replace)

Correction code 13058002 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

토크 규격

표 1. Torque Specifications: Armrest - 2nd Row (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
LH 암레스트 커버 패널을 2열 중앙 시트 프레임에 고정하는 나사
2.5 Nm (1.8 lbs-ft)
  • Torx T20 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse
2열 중앙 암레스트 Lobe 볼트
12 Nm (8.8 lbs-ft)
  • 10mm 소켓
  • 육각 헤드 래칫/플렉스 헤드 토크 렌치
Reuse

Remove

  1. 4개 도어를 모두 열고 모든 창문을 완전히 내립니다.
  2. 전면 좌석을 완전히 전방으로 이동합니다.
  3. 중앙 2열 시트 등받이 어셈블리를 아래로 접습니다.
  4. 중앙 2열 헤드레스트를 탈거합니다. Headrest - 2nd Row - Center (Remove and Replace)을(를) 참조하십시오.
  5. 중앙 2열 등받이 스위치를 탈거합니다. Backrest Switch – Seat Back – 2nd Row – Center (Remove and Replace)을(를) 참조하십시오.
  6. 트림 공구를 사용하여 중앙 후면 패널을 시트에 고정하는 클립을 좌석 하단에서 위쪽 방향으로 분리한 다음 시트 어셈블리에서 패널을 탈거합니다.
  7. LH 암레스트 커버 패널을 중앙 2열 시트 프레임에 고정하는 나사를 탈거한 후, 커버를 바깥 쪽과 시트프레임 상단 방향으로 들어 올려 탈거합니다. RH 암레스트 커버 패널에 대해서도 이 단계를 반복합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  8. LH 및 RH 암레스트 로브 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

    LH 표시; RH 유사함

  9. 작은 일자 드라이버를 사용하여 중앙 2열 시트 등받이 래치를 닫습니다.
  10. 중앙 2열 시트 등받이를 수직으로 세웁니다.
  11. 2열 암레스트를 당겨 중앙 2열 시트 등받이에서 분리합니다.

Install

  1. 2열 암레스트를 중앙 2열 시트 등받이에 장착합니다.
  2. 중앙 2열 시트 등받이 어셈블리를 아래로 접습니다.
  3. LH 및 RH 암레스트 로브 볼트를 장착합니다.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치

    LH 표시; RH 유사함

  4. 2열 시트 프레임에 LH 암레스트 커버 패널을 장착한 후, 패널을 시트 프레임에 고정하는 볼트를 장착합니다. RH 암레스트 커버 패널에 대해서도 이 단계를 반복합니다.
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • Torx T20 소켓
    • 육각 헤드 래칫/플렉스 헤드 토크 렌치
  5. 중앙 2열 시트 등받이 패널을 시트 프레임에 고정하는 후크를 체결한 후, 백패널의 하단부를 시트 프레임에 고정하는 클립(5개)을 체결합니다.
  6. 중앙 2열 등받이 스위치를 장착합니다. Backrest Switch – Seat Back – 2nd Row – Center (Remove and Replace)을(를) 참조하십시오.
  7. 중앙 2열 시트 등받이 래치를 분리합니다.
  8. 중앙 2열 시트 등받이 헤드레스트를 장착합니다.
  9. 중앙 2열 시트 등받이를 수직으로 세웁니다.
  10. 전면 시트를 원래 위치로 이동합니다.
  11. 모든 창문을 올리고 모든 도어를 닫습니다.