2026-10-15

플래터 인클로저 공기 누출 테스트 (구조용 팩)

교정 코드 16102030 0.50 메모: 절차에서 명시적으로 언급하지 않는 한 교정 코드 및 해당 관련 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  1. Disconnect LV power. See 12V/LV 전원(연결 해제 및 연결)
  2. Remove the rear aero shield. See 패널 - 에어로 실드 - 후면(탈거 및 교체).
  3. Perform the vehicle HV disablement procedure. See 차량 HV 비활성화 절차 (구조용 팩)
  4. Remove and discard the breather plugs (x4) from the thermal vents.
  5. Install the air splitter hoses onto the thermal vents.
  6. Connect the enclosure leak tester to the air splitter.
  7. Close both valves on the regulator test tool, and then connect the regulator to air supply.
  8. Turn the right side regulator valve to the open position.
  9. Set the regulator to 0.300 psi.
  10. Open the left side regulator valve to inject air into the ancillary bay.
    참고
    Allow 40 seconds fill time. Close the right side regulator valve when the pressure reaches 0.300 psi.
  11. Wait 15 seconds for the pressure to settle.
    • If pressure is below 0.285 psi, check the hose, adapter, plug fittings, and check the pressure regulator, then retest. If pressure is still below 0.285 psi, diagnose enclosure for leaks.
    • If pressure is at 0.285 psi or above, continue to the next step.
  12. Record the value of the starting pressure.
  13. Wait 30 seconds to test pressure.
  14. Record the value of the ending pressure.
  15. Subtract the ending pressure from the starting pressure.
    • If the difference is greater than 0.039 psi, then inspect the tools and retest. If the difference is still greater than 0.051 psi, then diagnose the enclosure for leaks.
    • If difference is 0.039 psi or less, then proceed with the current procedure.
  16. Disconnect the air supply from the regulator tool.
  17. Disconnect the enclosure leak tester from the air splitter.
  18. Remove the air splitter hoses (x4) from the thermal vents.
  19. Install new breather plugs (x4) onto the thermal vents.
    참고
    3x tabs per plug, Install new plugs, Press plug evenly, Make sure tabs are fully engaged and plug is flush with vent
  20. Install the rear drive unit HV cable connector to the HV battery and install other components that were removed to perform the vehicle HV disablement procedure. See 차량 HV 비활성화 절차 (구조용 팩).
    참고
    Make sure that the lever is in the upright and open position. Carefully seat the connector and allow the lever to engage. Fully install the lever and make sure that the locking tab is locked.
  21. Lower vehicle fully
    참고
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  22. Connect LV power. See 12V/LV 전원(연결 해제 및 연결).
  23. Remove vehicle from lift
    참고
    Lower rack arms fully and remove from under vehicle