2022-06-20

Panel Assembly - Rear (Remove and Replace)

Correction code 10102302 1.02 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

Torque Specifications

표 1. Torque Specifications: Panel Assembly - Rear (Remove and Replace)
Description Torque Value Recommended Tools Reuse/Replace Notes
후면 엔드 패널을 차체에 고정하는 볼트
10 Nm (7.4 lbs-ft)
  • 10mm 소켓
  • 4인치 익스텐션
Reuse
Bluetooth 패시브 엔트리 모듈을 후면 페시아 중앙 브래킷에 고정하는 볼트
3.5 Nm (2.6 lbs-ft)
  • 10mm 소켓
  • 4인치 익스텐션
Reuse

Remove

  1. LH 및 RH 테일라이트를 탈거합니다. Taillight - LH (Remove and Replace)을(를) 참조하십시오.
  2. 후면 페시아를 탈거합니다. Fascia - Rear (Remove and Install)을(를) 참조하십시오.
  3. 볼트를 탈거하고 Bluetooth 패시브 엔트리 모듈을 후면 페시아 중앙 브래킷에 고정하는 탭을 분리한 후, 하네스를 치워 놓습니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    브래킷에서 모듈을 분리할 때, LH 측을 돌려 브래킷에서 분리하고 탭을 분리합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 4인치 익스텐션
  4. 중앙 후면 브래킷을 탈거합니다. Bracket - Rear - Center (Remove and Replace)을(를) 참조하십시오.
  5. 후면 범퍼 빔 또는 트레일러 히치 어셈블리(해당하는 경우)를 탈거합니다. Bumper Beam - Rear (Remove and Replace) 또는 Assembly - Trailer Hitch (Remove and Replace)을(를) 참조하십시오.
  6. 하단 트렁크 어셈블리를 탈거합니다. Trunk Assembly - Lower (Remove and Replace)을(를) 참조하십시오.
  7. 후면 엔드 패널에서 후면 기본 씰을 들어 올립니다.
  8. 후면 엔드 패널을 차체에 고정하는 볼트를 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 4인치 익스텐션
  9. 차량에서 후방 엔드 패널을 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    후면 엔드 패널을 뒤쪽으로 밀어 차체로부터 패널을 풀어 놓습니다.

Install

  1. 차량에서 후방 엔드 패널을 배치합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    패널을 차체 스터드와 정렬합니다.
  2. 후면 엔드 패널을 차체에 고정하는 볼트를 장착합니다.
    10 Nm (7.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 4인치 익스텐션
  3. 후면 엔드 패널에 후면 기본 씰을 안착시킵니다.
  4. 하단 트렁크 어셈블리를 장착합니다. Trunk Assembly - Lower (Remove and Replace)을(를) 참조하십시오.
  5. 후면 범퍼 빔 또는 트레일러 히치 어셈블리(해당하는 경우)를 장착합니다. Bumper Beam - Rear (Remove and Replace) 또는 Assembly - Trailer Hitch (Remove and Replace)을(를) 참조하십시오.
  6. 중앙 후면 브래킷을 장착합니다. Bracket - Rear - Center (Remove and Replace)을(를) 참조하십시오.
  7. Bluetooth 패시브 엔트리 모듈을 후면 페시아 중앙 브래킷에 고정하는 볼트와 탭을 장착합니다.
    3.5 Nm (2.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    좌측을 안쪽 방향으로 돌려 탭을 장착합니다.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Use of the following tool(s) is recommended:
    • 10mm 소켓
    • 4인치 익스텐션
  8. 후면 페시아를 장착합니다. Fascia - Rear (Remove and Install)을(를) 참조하십시오.
  9. LH 및 RH 테일라이트를 장착합니다. Taillight - LH (Remove and Replace)을(를) 참조하십시오.