2025-09-11

Module - HomeLink Transmitter (Remove and Replace)

Correction code 17154202 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 개인 보호 to make sure wearing proper PPE when performing the below procedure. See 인체공학적 주의 사항 for safe and healthy working practices.

  • 2025-07-14: 교체 이후 루틴 지침을 업데이트했습니다.
  • 2024-06-03: 홈링크 아이콘을 확인하기 위해 정비 모드를 종료하라는 참고 사항을 추가했습니다.

Remove

  1. 후면 후드 내 에이프런을 탈거합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).
  2. 12V 전원을 분리합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  3. 후드 내 보관 유닛을 탈거합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  4. 커넥터 잠금 장치를 해제한 다음 홈링크 모듈에서 전기 커넥터를 연결 해제합니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling the main body of the connector to fully disconnect it.
  5. Homelink 모듈을 뒤쪽으로 들어올려 외측으로 밀어 브래킷에서 탭을 연결 해제한 다음 모듈을 차량에서 탈거합니다.

Install

  1. Homelink 모듈을 차량에 장착합니다.
  2. 전기 커넥터를 Homelink 모듈에 연결한 다음 커넥터 잠금 장치를 체결합니다.
  3. 후드 내 보관 유닛을 장착합니다. 참조 항목: Underhood Storage Unit (Remove and Replace).
  4. 12V 전원을 다시 연결합니다. 참조 항목: 12V/LV Power (Disconnect and Connect).
  5. Toolbox에서 Actions/Autodiag(작업/자동 진단) 탭을 클릭한 다음 “HOMELINK”를 검색합니다.
  6. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST-SELF_VCFRONT_X_HOMELINKvia Toolbox: (link)via Service Mode: Low Voltage ➜ HomeLink ➜ Test HomeLink
  7. 차량 터치스크린에서 홈링크 아이콘이 보이는지 확인합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    홈링크 아이콘은 차량이 정비 모드에 있는 경우에는 활성화되지 않습니다. 필요한 경우 정비 모드를 종료하여 확인합니다.
  8. 후면 후드 내 에이프런을 장착합니다. 참조 항목: Underhood Apron - Rear (Remove and Replace).