Module - contrôleur de carrosserie - droit (conduite à gauche) (pompe à chaleur) (retirez et remplacez)
Code de correction
17152212 0.90 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire.REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires au LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.
- 2025-03-10: Updated post-replacement routine.
- 2023-07-14: Updated procedure to latest GSD validation for M3.
Retirer
- Open the front doors and lower the windows.
- Remove the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
- Disconnect 12V power. See Alimentation 12 V/BT (déconnectez et connectez).
- Remove the LH instrument panel end cap. See Capuchons d’extrémité - tableau de bord - gauche (retirez et remplacez).
- Remove the LH air wave end cap. See Capuchons d’extrémité - onde d’air - gauche (retirez et remplacez).
- Repeat steps 4 and 5 for the RH side of the vehicle.
- Remove the main instrument panel decor trim. See Garniture décorative - tableau de bord - principal (retirez et remplacez).
- Remove the RH middle A-pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
- Remove the RH lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
- Remove the passenger footwell cover. See Couvercle - espace pour les jambes - passager (conduite à gauche) (retirez et remplacez).
- Remove the front passenger knee airbag (if equipped). See Coussin gonflable - genou - passager avant (retirez et remplacez).
- Remove the glove box. See Boîte à gants - avec coussins gonflables pour les genoux (pompe sans chaleur) (retirez et remplacez) or Boîte à gants - sans coussins gonflables pour les genoux (retirez et remplacez).
- Remove the RH front floor mat.
- Remove the RH center console side panel carpet. See Panneau latéral - console centrale - gauche (retirez et remplacez).
- Release the clips (x3) that attach the RH front carpet to the body at the RH A-pillar.
-
Fold back the RH front carpet.
NoteRelease the seat harness from the clips at the RH door sill to allow the carpet to further fold back.
-
Remove the nuts (x2) that attach the RH side carpet locator bracket.
NoteLater vehicles may use 2x push clips instead.
- Release the connector lock, and then disconnect the J7 door electrical connector from the RH body controller module.
- Release the connector lock, and then disconnect the J9 front passenger seat electrical connector from the RH body controller module.
- Disconnect the J10 instrument panel electrical connector from the RH body controller module.
- Disconnect the J11 HVAC electrical connector from the RH body controller module.
- Release the connector lock, and then disconnect the J1 power electrical connector from the RH body controller module.
- Release the connector lock, and then disconnect the J4 body electrical connector from the RH body controller module.
- Disconnect the RH body harness connector.
- Release the harness clips below the IP carrier.
- Disconnect the J6 underhood storage unit electrical connector from the RH body controller module.
- Release the connector lock, and then disconnect the J2 body electrical connector from the RH body controller module.
- Disconnect the J12 body electrical connector from the RH body controller module.
- Disconnect the J5 body electrical connector from the RH body controller module.
- Disconnect the connectors from the harness clip at the RH lower A-pillar area.
- Remove the RH body harness clip from the lower A-pillar area.
- Remove the RH body harness clips from the RH body controller module.
- Move the RH body harness away from the RH body controller module.
-
Remove and discard the nyloc nut that attaches the RH body controller module to the vehicle.
NoteNous recommandons l’utilisation des outils suivants :
- Slide the RH body controller module upwards to release the W clip, maneuver the RH body controller module out from under the IP, and then remove the RH body controller module from the vehicle.
Installer
- Maneuver RH body controller module into position under the IP carrier, align the W clip with the body cut out, and then slide down the RH body controller module to secure it.
-
Install a new nyloc nut that attaches the RH body controller module to the vehicle (torque 6 Nm).
RemarqueNous recommandons l’utilisation des outils suivants :
- Move the RH body harness towards the RH body controller module.
- Install the RH body harness clips to the RH body controller module.
- Install the RH body harness clip to the RH lower A-pillar area.
- Connect the connectors at the harness clip at the RH lower A-pillar area.
- Connect the J5 body electrical connector to the RH body controller module.
- Connect the J12 body electrical connector to the RH body controller module.
- Connect the J2 body electrical connector to the RH body controller module: fully seat the connector, and then engage the lock.
- Connect the J6 underhood storage unit electrical connector to the RH body controller module.
- Connect the J1 power electrical connector to the RH body controller module.
- Connect the J4 body electrical connector to the RH body controller module.
- Connect the connector of the RH body harness.
- Connect the J11 HVAC electrical connector to the RH body controller module.
- Connect the J10 instrument panel electrical connector to the RH body controller module.
- Connect the J9 front passenger seat electrical connector to the RH body controller module.
- Connect the J7 door electrical connector to the RH body controller module.
- Install the harness clips below the IP carrier.
-
Install the nuts (x2) that attach the RH side carpet locator bracket (torque 2.5 Nm).
RemarqueLater vehicles may use push clips instead of nuts.
- Unfold the RH front carpet, and then reinstall the harness into the clips at the RH door sill.
- Install the clips (x3) that attach the RH front carpet to the body.
- Install the RH center console side panel carpet. See Panneau latéral - console centrale - gauche (retirez et remplacez).
- Install the RH front floor mat.
- Install the glove box. See Boîte à gants - avec coussins gonflables pour les genoux (pompe sans chaleur) (retirez et remplacez) or Boîte à gants - sans coussins gonflables pour les genoux (retirez et remplacez).
- Install the front passenger knee airbag (if equipped). See Coussin gonflable - genou - passager avant (retirez et remplacez).
- Install the passenger footwell cover. See Couvercle - espace pour les jambes - passager (conduite à gauche) (retirez et remplacez).
- Install the RH lower A-pillar trim. See Garniture - montant avant - inférieure - gauche (retirez et remplacez).
- Install the RH middle A-pillar trim. See Garniture - montant avant - milieu - gauche (retirez et remplacez).
- Install the main instrument panel decor trim. See Garniture décorative - tableau de bord - principal (retirez et remplacez).
- Install the RH air wave end cap. See Capuchons d’extrémité - onde d’air - gauche (retirez et remplacez).
- Install the RH instrument panel end cap. See Capuchons d’extrémité - tableau de bord - gauche (retirez et remplacez).
- Repeat steps 30 and 31 for the LH side of the vehicle.
- Connect 12V/LV power. See Alimentation 12 V/BT (déconnectez et connectez).
- Install the rear underhood apron. See Tablier sous le capot - arrière (retirez et remplacez).
-
Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) :
UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
- Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
- Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
- Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
- Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
- Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
- Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
- chassis ➜ DPB Post Replacement ➜ CAN Redeploy
- chassis ➜ ESP Post Replacement ➜ CAN Redeploy
- chassis ➜ IDB Post Replacement ➜ CAN Redeploy
- chassis ➜ RCU Post Replacement ➜ CAN Redeploy
- chassis ➜ ESP Replacement Panel ➜ CAN Redeploy
- chassis ➜ IBST Replacement Panel ➜ CAN Redeploy
- Once firmware redeploy is complete, verify on the center display that the release notes are present.
- Sit in the driver seat and close the LH front door.
-
Exécutez la routine suivante au moyen du mode Entretien ou de Toolbox (consultez 0005 – Modes d’entretien) :
RemarqueKeep the front passenger seat clear of any objects during calibration.
- Close the front doors and raise the windows.