08/04/2024 10:56:05

Tuyau - contournement du groupe motopropulseur de l’unité d’entraînement avant (pompe à chaleur) (traction arrière) (retirez et remplacez)

Code de correction 18302302 0.55 REMARQUE : À moins d’indications explicites contraires dans la procédure, le code de correction et le temps forfaitaire ci-dessus représentent tout le travail à être fait pour cette procédure, notamment les procédures connexes. N’appliquez pas plusieurs codes de correction à la fois, à moins qu’il vous soit explicitement indiqué de le faire. REMARQUE : Consultez Temps forfaitaires pour en apprendre plus à propos des temps forfaitaires et de leur création. Vous pouvez transmettre par courriel vos commentaires relatifs aux valeurs des temps forfaitaires à LaborTimeFeedback@tesla.com. REMARQUE : Consultez Protection individuelle pour vous assurer de porter l’équipement de protection individuelle adéquat lors vous effectuez la procédure ci-dessous.

Avertissement

Cette procédure est un BROUILLON, même si elle a été validée. Il peut manquer des avertissements et des mises en garde. Respectez les exigences de sécurité et faites preuve d’une extrême prudence lorsque vous travaillez sur ou près de systèmes et de composants haute tension. Transmettez toute correction ou remarque à ServiceDevelopment@teslamotors.com.

Retirer

Raise and support vehicle
Open LH front door
Lower LH front window
Open hood

Remarque
Press "Open" button on touchscreen to release latch, Lift lid manually
Remove rear apron

Remarque
12x clips, Only store rear apron visible face upwards
Remove cabin intake upper duct assembly

Remarque
3x clips, Some configurations may come with 4x clips
Power off vehicle from center display

Remarque
Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
Disconnect 12V negative terminal

Remarque
1x nut, 10mm, 6 Nm, Ensure vehicle is in park, climate control system is off, and vehicle is not charging before disconnecting 12V
Disconnect first responder loop

Remarque
1x connector, Release locking tab
Raise vehicle fully and lower lift onto locks

Remarque
Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side, Verify doors are clear of surrounding objects
Remove outer fasteners securing front aero shield

Remarque
9x bolts, 10mm, 5 Nm
Remove remaining nuts and remove front aero shield from vehicle

Remarque
2x nuts, 15mm, 5 Nm
Remove clips securing RH front wheel liner to vehicle

Remarque
4x clips
Use bungee strap to pull back RH front wheel liner

Remarque
Secure to subframe
Position coolant drain container underneath RH front of HV battery
Disconnect PT return tube from FDU bypass hose

Remarque
2x clips, 2x plugs, Lower hose located on RH front of HV battery, Plug both hose ends
Remove coolant drain container from underneath vehicle

Installer

Release FDU bypass hose from front subframe

Remarque
1x fir tree clip
Lower vehicle

Remarque
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
Position fluid catcher underneath front of vehicle
Disconnect FDU bypass hose from the Supermanifold and remove from vehicle

Remarque
1x spring clip, 2x plugs, Plug supermanifold and bypass hose to prevent excess coolant drain
Feed hose into position and install FDU bypass hose to the supermanifold

Remarque
1x spring clip, 2x plugs, Install plug onto lower end of hose to avoid coolant loss, Remove plug from Supermanifold, Perform push-pull-push test to make sure hose is fully engaged
Remove fluid catcher from underneath vehicle
Raise vehicle fully and lower lift onto locks

Remarque
Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
Secure FDU bypass hose to front subframe

Remarque
1x fir tree clip
Position coolant drain container underneath RH front of HV battery
Remove plugs then connect PT return tube to FDU bypass hose

Remarque
2x clips, 2x plugs, Perform push-pull-push test to make sure hoses are fully engaged
Remove coolant drain container from underneath vehicle
Release RH front wheel liner from bungee strap

Remarque
Remove strap from vehicle
Install clips securing RH front wheel liner to vehicle

Remarque
4x clips
Position front aero shield to vehicle and install nuts

Remarque
2x nuts, 15mm, 5 Nm
Apply Loctite 222 onto front aero shield bolts and install outer fasteners to front aero shield

Remarque
9x bolts, 10mm, 5 Nm
Lower vehicle fully

Remarque
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Install frunk assembly to vehicle

Remarque
12x clips, Make sure frunk assembly is fully seated onto clips, Number of clips may vary on older vehicles. Ensure A/C compressor HVIL harness is not pinched between frunk assembly and thermal beam
Install bolts securing frunk assembly

Remarque
7x bolts, 10mm, 5 Nm, Lower RBN covers after installing upper fasteners, Newer vehicles may not be equipped with covers
Install frunk close out panel

Remarque
4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push downward to secure clips
Remove coolant bottle cap
Inspect coolant level and top off as necessary

Remarque
Ensure that fluid level is at Max line
Connect first responder loop

Remarque
1x connector, Engage locking tab, Connect FRL before connecting 12V to avoid damage to car computer
Connect 12V negative terminal

Remarque
1x nut, 10mm, 6 Nm
Connect to vehicle using Toolbox 3.0

Remarque
Vehicle connection is integrated into drivers footwell cover, Open Toolbox 3 website and establish connection to the vehicle, https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)If RJ45 ethernet diagnostic connector present connect directly from laptop using an RJ45 Ethernet cable
Select ‘Actions/Autodiag’ tab and search for ‘Purge'
Select ‘TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGE ’, click ‘Run’, and allow routine to complete

Remarque
Make sure vehicle is not in drive state, Plan is still running despite the stop message, Coolant pumps will be audible, Test lasts approximately 10 mins, Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valve between SERIES and PARALLEL, Putting vehicle into drive state will stop this routine, If speeds hover at 7000 RPM, that means the pumps are air locked, perform vacuum fill again, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle, Select ‘X’ at top right of window to close once complete
Remove HSD or RJ45 cable from Ethernet port to disconnect Toolbox 3.0 from vehicle
Inspect coolant level and top off as necessary

Remarque
Ensure that fluid level is at Max line
Install coolant bottle cap
Install cabin intake upper duct assembly

Remarque
3x clips, Some configurations may come with 4x clips
Install rear apron

Remarque
12x clips
Close hood
Raise LH front window
Close LH front door
Remove vehicle from lift

Remarque
Lower rack arms fully and remove from under vehicle