Model 3 Service Manual

1601 – Ensemble batterie haute tension

Liens connexes

Batterie HT (AWD) (retirez et installez)
Codes de correction 16010201 3.48 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when performing the below procedure.
Batterie HT (AWD) (retirez et remplacez)
Codes de correction 16010202 5.40 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when performing the below procedure.
Batterie HT (traction arrière) (retirez et installez)
Codes de correction 16010101 3.42 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when performing the below procedure.
Batterie HT (traction arrière) (retirez et remplacez)
Codes de correction 16010102 5.46 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so.NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email LaborTimeFeedback@tesla.com. NOTE: See Protection individuelle to make sure wearing proper PPE when performing the below procedure.

Sujet parent : 16 – Système de batterie

Manuel d’entretien Model 3
Notes de mise à jour
Renseignements généraux
00 – Inspection et entretien
10 – Carrosserie
11 – Fermetures
12 – Accessoires extérieurs
13 – Sièges
14 – Tableau de bord
- Caractéristiques techniques de couple – Tableau de bord
- 1405 – Tableau de bord
15 – Garniture intérieure
16 – Système de batterie
17 – Système électrique
18 – Gestion thermique
20 – Sécurité et systèmes de retenue
21 – Infodivertissement
30 – Châssis
- Caractéristiques techniques de couple – Châssis
- 3001 – Châssis et châssis auxiliaires
31 – Suspension
32 – Direction
33 – Freins
34 – Roue et pneus
39 – Unité d’entraînement avant
40 – Unité d’entraînement arrière
44 – Système haute tension
50 – Connecteurs de chargement externes
- 5001 – Connecteur mobile
  - Mise à jour du micrologiciel - Connecteur mobile
  - Retirer l’écran isolant - poignée de recharge
- 5003 - Adaptateurs de recharge
  - Mise à jour de micrologiciel - adaptateur de recharge CHAdeMO

© Tesla 2025
Procedure Feedback
Site Feedback

Crowsfoot or Offset Wrench Extension Calculator

Torque Calculator Values

T1 (Original torque spec)

L (Distance from center of wrench grip to center of square drive tang)

E (Horizontal distance from center of square drive tang to center of fastener)

Note

If the angle from the extension to the torque wrench is greater than 90° (Figure 2), input E as a positive number.
If the angle from the extension to the torque wrench is less than 90° (Figure 3), input E as a negative number.
If the angle from the extension to the torque wrench is exactly 90°, this calculator is not needed. Torque the fastener to T1.

T2 (Final torque setting)